はじめに
今回は予定を変更して「Intel Galileo Development Board」上で動作するLinuxから、Intel Quark SoC X1000やIntel Galileo Development Boardがどのように見えているのか、各種ログを紹介したいと思います。当初は“「Intel Galileo Development Board」を起動して動作確認”で一緒に載せようと思っていたのですが、サイズが大きくなってしまったので別の記事にすることにしたものです。
ログの内容が長いので、それぞれ閉じた状態にしておきます。必要な個所を開いてご覧ください。
関連ページ
- 「Intel Galileo Development Board」を試用してみての感想
- 「Intel Galileo Development Board」でLEDの発光を制御
- 「Intel Galileo Development Board」を起動して動作確認
- 「Intel Galileo Development Board」を使用する準備
- 「Intel Galileo Development Board」を使用するために必要なもの
- 写真で見る「Intel Galileo Development Board」
試用している「Intel Galileo Development Board」などについて
- 本記事で試用している「Intel Galileo Development Board」は、インテル株式会社より“さかきけい”個人に貸し出されたものです。このため私の勤務先等とは一切関係がありません。
- 本記事は“さかきけい”が完全に自由意思で書いているもので、インテル株式会社からは何らの要請、制限等は受けていません（あるのは返却期限のみです）。
- ボードのリビジョンは「量産前」のもので、Maker Faire RomeでIntel CEOのBrian M. Krzanichさんが発表した際に同会場で配布されたものと同等とのことです。
- 海外仕様そのままなので「インテル Galileo 開発ボード」ではなく、あえて「Intel Galileo Development Board」と記述しています。
- 日本で発売される「量産品」と仕様あるいは内容物が同等であるかは不明とのことです。
ブートログ（ファームウェア更新前）
Ethernetに接続がない状態で起動したログです：
Found layout.conf @ 0xfff08200 len 0x00000d12
#Generated by Buildbot - Sysimage 732
#EXAMPLE LAYOUT.CONF FILE FOR FPGA/RELEASE
# WARNING: this file is indirectly included in a Makefile where it
# defines Make targets and pre-requisites. As a consequence you MUST
# run "make clean" BEFORE making changes to it. Failure to do so may
# result in the make process being unable to clean files it no longer
# has references to.
[main]
size=8388608
type=global
[MFH]
version=0x1
flags=0x0
address=0xfff08000
type=mfh
[LAYOUT.CONF_DUMP]
address=0xfff08200
type=mfh.build_information
meta=layout
[Flash Image Version]
type=mfh.version
meta=version
value=732
[ROM_OVERLAY]
address=0xfffe0000
#item_file=/p/clanton/swbuilds/BootRom/Ver_1_00_09/Clanton.rom
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOTROM_OVERRIDE.Fv
type=some_type
in_capsule=no
[signed-key-module]
address=0xfffd8000
item_file=config/SvpSignedKeyModule.bin
svn_index=0
type=some_type
[svn-area]
address=0xfffd0000
item_file=config/SVNArea.bin
type=some_type
[fixed_recovery_image]
address=0xfff90000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_RECOVERY_IMAGE1.Fv
sign=yes
type=mfh.host_fw_stage1_signed
svn_index=2
in_capsule=no
[NV_Storage]
address=0xfff30000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_NVRAM.bin
type=some_type
[RMU]
address=0xfff00000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/RMU.bin
type=none_registered
[boot_stage1_image1]
address=0xffec0000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE1_IMAGE1.Fv
sign=yes
boot_index=0
type=mfh.host_fw_stage1_signed
svn_index=1
[boot_stage1_image2]
address=0xffe80000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE1_IMAGE2.Fv
sign=yes
boot_index=1
type=mfh.host_fw_stage1_signed
svn_index=1
[boot_stage_2_compact]
address=0xffd00000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE2_COMPACT.Fv
sign=yes
type=mfh.host_fw_stage2_signed
svn_index=3
#address=0x002E1000
[Ramdisk]
address=0xffa60000
item_file=/p/clanton/swbuilds/meta-clanton_spi/meta-cln_spi_00103/image-spi-clanton.cpio.lzma
sign=yes
type=mfh.ramdisk_signed
svn_index=7
[Kernel]
address=0xff851600
item_file=/p/clanton/swbuilds/meta-clanton_spi/meta-cln_spi_00103/bzImage
sign=yes
type=mfh.kernel_signed
svn_index=6
[grub.conf]
address=0xff850500
item_file=grub/grub-ce.conf
sign=yes
type=mfh.bootloader_conf_signed
svn_index=5
[grub]
address=0xff800000
item_file=/p/clanton/swbuilds/meta-clanton_spi/meta-cln_spi_00103/grub.efi
sign=yes
fvwrap=yes
guid=B43BD3E1-64D1-4744-9394-D0E1C4DE8C87
type=mfh.bootloader_signed
svn_index=4
# strings -n 16 '/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00366/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE1_IMAGE1.Fv' | grep -i 'clanton.*version' | head | unix2dos
# Clanton RomCode Version
# Clanton Microcode Version a0_1_00_23
[Linux-EFI SPI, setup=0x1070, size=0x1ef8f0]
[Initrd SPI, addr=0xdd77000, size=0x282954]
[ 12.567555] console [ttyS1] enabled, bootconsole disabled
[ 12.580599] Real Time Clock Driver v1.12b
[ 12.597864] brd: module loaded
[ 12.615359] cpuidle: using governor ladder
[ 12.619527] cpuidle: using governor menu
[ 12.632513] THRM: critical reset 86 c hot 70 c hardware failover 105 c
[ 12.644685] TCP: cubic registered
[ 12.648071] NET: Registered protocol family 17
[ 12.653956] ... APIC ID: 00000000 (0)
[ 12.658087] ... APIC VERSION: 00030010
[ 12.662067] 0000000000000000000000000000000000000000000000000000000000000000
[ 12.662608] 0000000000000000000000000000000000000000000000000000000000000000
[ 12.662608] 0000000000000000000000000000000000000000000000000000000000008000
[ 12.662608]
[ 12.685814] testing the IO APIC.......................
[ 12.693223] .................................... done.
[ 12.698401] Using IPI Shortcut mode
[ 12.715223] Magic number: 1:0:0
[ 12.733100] Freeing unused kernel memory: 268k freed
[ 12.741032] Write protecting the kernel text: 2984k
[ 12.747060] Write protecting the kernel read-only data: 1232k
[ 12.752984] NX-protecting the kernel data: 3160k
[ 12.760577] Failed to execute /init
INIT: version 2.88 booting
[ 13.011266] tsc: Refined TSC clocksource calibration: 399.076 MHz
[ 13.017603] Switching to clocksource tsc
[ 13.145686] sdhci: Secure Digital Host Controller Interface driver
[ 13.152044] sdhci: Copyright(c) Pierre Ossman
[ 13.162669] sdhci-pci 0000:00:14.0: SDHCI controller found [8086:08a7] (rev 10)
[ 13.242480] mmc0: SDHCI controller on PCI [0000:00:14.0] using ADMA
[ 13.539000] g_serial: Vendor 0x8086 Product 0xbabe
[ 13.558418] g_serial gadget: Gadget Serial v2.4
[ 13.571920] g_serial gadget: g_serial ready
[ 13.647199] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 13.654849] stmmac MSI mode enabled
[ 13.658212] Vendor 0x8086 Device 0x0937
[ 13.662564] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 13.667666] DMA HW capability register supported
[ 13.672353] Enhanced/Alternate descriptors
[ 13.676776] RX Checksum Offload Engine supported (type 2)
[ 13.682416] TX Checksum insertion supported
[ 13.686737] Enable RX Mitigation via HW Watchdog Timer
[ 13.743709] libphy: stmmac: probed
[ 13.747178] eth0: PHY ID 20005c90 at 1 IRQ 0 (stmmac-1:01) active
[ 13.819332] ACPI: bus type usb registered
[ 13.827135] usbcore: registered new interface driver usbfs
[ 13.835013] usbcore: registered new interface driver hub
[ 13.843196] usbcore: registered new device driver usb
[ 13.858360] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.911626] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.918454] ohci_hcd 0000:00:14.4: OHCI Host Controller
[ 13.925477] ohci_hcd 0000:00:14.4: new USB bus registered, assigned bus number 1
[ 13.933341] ohci_hcd 0000:00:14.4: irq 16, io mem 0x9000c000
[ 14.011253] hub 1-0:1.0: USB hub found
[ 14.015675] hub 1-0:1.0: 2 ports detected
[ 14.083817] Initializing USB Mass Storage driver...
[ 14.091040] usbcore: registered new interface driver usb-storage
[ 14.097101] USB Mass Storage support registered.
[ 14.285266] cy8c9540a 0-0020: dev_id=0x40
[ 14.437291] i2c /dev entries driver
[ 14.605274] ce4100_spi 0000:00:15.0: enabling device (0000 -> 0002)
[ 14.612350] pci spi probe(), enable_msi 1, mmio_base e0772000, dev c01c8800
[ 14.620240] MSI enabled, irq number is 43
[ 14.624295] ssp type is CE5X00 SSP
[ 14.630795] ce4100_spi 0000:00:15.1: enabling device (0000 -> 0002)
[ 14.637323] pci spi probe(), enable_msi 1, mmio_base e0774000, dev c01c9000
[ 14.645586] MSI enabled, irq number is 44
[ 14.649640] ssp type is CE5X00 SSP
[ 14.708096] pxa2xx-spi pxa2xx-spi.0: master is unqueued, this is deprecated
[ 14.725144] pxa2xx-spi pxa2xx-spi.1: master is unqueued, this is deprecated
Starting Bootlog daemon: bootlogd.
Configuring network interfaces... [ 17.643466] eth0: device MAC address **:**:**:**:**:**
udhcpc (v1.20.2) started
Sending discover...
Sending discover...
Sending discover...
No lease, failing
kernel.hotplug = /sbin/mdev
sh: %4Y%2m%2d%2H%2M: bad number
INIT: Entering runlevel: 5
Starting syslogd/klogd: done
Stopping Bootlog daemon: bootlogd.
/sketch/sketch.elf file does not exist or invalid permissions
clloader waiting to receive.
Poky 9.0 (Yocto Project 1.4 Reference Distro) 1.4.1 clanton /dev/ttyS1
clanton login: ブートログ（ファームウェア更新後）
Ethernetに接続があり、LAN内にDHCPサーバーが動作している状態で起動したログです：
Found layout.conf @ 0xffcff000 len 0x00000d18
#Generated by Buildbot - Sysimage 782
#EXAMPLE LAYOUT.CONF FILE FOR FPGA/RELEASE
# WARNING: this file is indirectly included in a Makefile where it
# defines Make targets and pre-requisites. As a consequence you MUST
# run "make clean" BEFORE making changes to it. Failure to do so may
# result in the make process being unable to clean files it no longer
# has references to.
[main]
size=8388608
type=global
[MFH]
version=0x1
flags=0x0
address=0xfff08000
type=mfh
[Flash Image Version]
type=mfh.version
meta=version
value=782
[ROM_OVERLAY]
address=0xfffe0000
#item_file=/p/clanton/swbuilds/BootRom/Ver_1_00_09/Clanton.rom
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOTROM_OVERRIDE.Fv
type=some_type
# in_capsule=no
[signed-key-module]
address=0xfffd8000
item_file=config/SvpSignedKeyModule.bin
svn_index=0
type=some_type
[svn-area]
address=0xfffd0000
item_file=config/SVNArea.bin
type=some_type
[fixed_recovery_image]
address=0xfff90000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_RECOVERY_IMAGE1.Fv
sign=yes
type=mfh.host_fw_stage1_signed
svn_index=2
# in_capsule=no
[NV_Storage]
address=0xfff30000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_NVRAM.bin
type=some_type
[RMU]
address=0xfff00000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/RMU.bin
type=none_registered
[boot_stage1_image1]
address=0xffec0000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE1_IMAGE1.Fv
sign=yes
boot_index=0
type=mfh.host_fw_stage1_signed
svn_index=1
[boot_stage1_image2]
address=0xffe80000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE1_IMAGE2.Fv
sign=yes
boot_index=1
type=mfh.host_fw_stage1_signed
svn_index=1
[boot_stage_2_compact]
address=0xffd00000
item_file=/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE2_COMPACT.Fv
sign=yes
type=mfh.host_fw_stage2_signed
svn_index=3
#address=0x002E1000
[Ramdisk]
address=0xffa60000
item_file=/p/clanton/swbuilds/meta-clanton_spi/meta-cln_spi_00157/image-spi-clanton.cpio.lzma
sign=yes
type=mfh.ramdisk_signed
svn_index=7
[LAYOUT.CONF_DUMP]
address=0xffcff000
type=mfh.build_information
meta=layout
[Kernel]
address=0xff852000
item_file=/p/clanton/swbuilds/meta-clanton_spi/meta-cln_spi_00157/bzImage
sign=yes
type=mfh.kernel_signed
svn_index=6
[grub.conf]
address=0xff851000
item_file=grub/grub-ce.conf
sign=yes
type=mfh.bootloader_conf_signed
svn_index=5
[grub]
address=0xff800000
item_file=/p/clanton/swbuilds/meta-clanton_spi/meta-cln_spi_00157/grub.efi
sign=yes
fvwrap=yes
guid=B43BD3E1-64D1-4744-9394-D0E1C4DE8C87
type=mfh.bootloader_signed
svn_index=4
# strings -n 16 '/p/clanton/swbuilds/EDK2/edk2_gcc_CP_00388/ClantonPeakCRBPlatform/RELEASE_GCC/FV/FlashModules/EDKII_BOOT_STAGE1_IMAGE1.Fv' | grep -i 'clanton.*version' | head | unix2dos
# Clanton RomCode Version
# Clanton Microcode Version a0_1_00_23
[Linux-EFI SPI, setup=0x1070, size=0x200620]
[Initrd SPI, addr=0xdd5f000, size=0x2647b1]
[ 12.126614] console [ttyS1] enabled, bootconsole disabled
[ 12.139588] Real Time Clock Driver v1.12b
[ 12.157103] brd: module loaded
[ 12.176023] loop: module loaded
[ 12.181613] lpc_sch_probe BIOS_CNTL 0x00000101
[ 12.186131] lpc_sch_probe new BIOS_CNTL 0x00000101
[ 12.191116] lpc_sch_probe RCBA @ 0xfed1c000
[ 12.219160] cpuidle: using governor ladder
[ 12.223800] cpuidle: using governor menu
[ 12.229001] sdhci: Secure Digital Host Controller Interface driver
[ 12.235361] sdhci: Copyright(c) Pierre Ossman
[ 12.240490] sdhci-pci 0000:00:14.0: SDHCI controller found [8086:08a7] (rev 10)
[ 12.300252] mmc0: SDHCI controller on PCI [0000:00:14.0] using ADMA
[ 12.313357] sdhci-pltfm: SDHCI platform and OF driver helper
[ 12.344334] THRM: critical reset 104 c hot 95 c hardware failover 105 c
[ 12.375589] TCP: cubic registered
[ 12.378977] NET: Registered protocol family 17
[ 12.384753] ... APIC ID: 00000000 (0)
[ 12.388889] ... APIC VERSION: 00030010
[ 12.392908] 0000000000000000000000000000000000000000000000000000000000000000
[ 12.393514] 0000000000000000000000000000000000000000000000000000000000000000
[ 12.393514] 0000000000000000000000000000000000000000000000000000000000008000
[ 12.393514]
[ 12.416754] testing the IO APIC.......................
[ 12.424478] .................................... done.
[ 12.429659] Using IPI Shortcut mode
[ 12.448749] Magic number: 9:489:690
[ 12.452861] mem mem: hash matches
[ 12.497911] Freeing unused kernel memory: 272k freed
[ 12.513656] Write protecting the kernel text: 3100k
[ 12.519776] Write protecting the kernel read-only data: 1284k
[ 12.525703] NX-protecting the kernel data: 3044k
[ 12.533221] Failed to execute /init
[ 12.551580] tsc: Refined TSC clocksource calibration: 399.076 MHz
[ 12.557914] Switching to clocksource tsc
INIT: version 2.88 booting
[ 13.040538] g_serial: Vendor 0x8086 Product 0xbabe
[ 13.045482] g_serial gadget: Gadget Serial v2.4
[ 13.051600] g_serial gadget: g_serial ready
[ 13.110573] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 13.117667] stmmac MSI mode enabled
[ 13.121162] Vendor 0x8086 Device 0x0937
[ 13.125851] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 13.131083] DMA HW capability register supported
[ 13.135661] Enhanced/Alternate descriptors
[ 13.140197] RX Checksum Offload Engine supported (type 2)
[ 13.145732] TX Checksum insertion supported
[ 13.150156] Enable RX Mitigation via HW Watchdog Timer
[ 13.205560] libphy: stmmac: probed
[ 13.209028] eth0: PHY ID 20005c90 at 1 IRQ 0 (stmmac-1:01) active
[ 13.280541] ACPI: bus type usb registered
[ 13.288150] usbcore: registered new interface driver usbfs
[ 13.296006] usbcore: registered new interface driver hub
[ 13.304188] usbcore: registered new device driver usb
[ 13.319231] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.374398] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.382287] ohci_hcd 0000:00:14.4: OHCI Host Controller
[ 13.388864] ohci_hcd 0000:00:14.4: new USB bus registered, assigned bus number 1
[ 13.396764] ohci_hcd 0000:00:14.4: irq 16, io mem 0x9000c000
[ 13.480930] hub 1-0:1.0: USB hub found
[ 13.485336] hub 1-0:1.0: 2 ports detected
[ 13.543588] ehci-pci: EHCI PCI platform driver
[ 13.548709] ehci-pci 0000:00:14.3: EHCI Host Controller
[ 13.554722] ehci-pci 0000:00:14.3: new USB bus registered, assigned bus number 2
[ 13.563504] ehci-pci 0000:00:14.3: INSNREG01 is 0x007f007f
[ 13.569058] ehci-pci 0000:00:14.3: INSNREG01 is 0x007f007f
[ 13.574966] ehci-pci 0000:00:14.3: irq 19, io mem 0x9000d000
[ 13.600228] ehci-pci 0000:00:14.3: USB 2.0 started, EHCI 1.00
[ 13.612747] hub 2-0:1.0: USB hub found
[ 13.616755] hub 2-0:1.0: 2 ports detected
[ 13.640310] g_serial gadget: high-speed config #1: CDC ACM config
[ 13.691229] Initializing USB Mass Storage driver...
[ 13.698424] usbcore: registered new interface driver usb-storage
[ 13.704612] USB Mass Storage support registered.
[ 13.841949] intel_cln_gpio_probe UIO addr 0x90006000 internal_addr 0x00000000 size 3765649408 memtype 4096
[ 13.914838] cy8c9540a 0-0020: dev_id=0x40
[ 14.073881] at24 0-0050: byte_len looks suspicious (no power of 2)!
[ 14.080856] at24 0-0050: 11264 byte at24 EEPROM, writable, 1 bytes/write
[ 14.134436] i2c /dev entries driver
[ 14.298728] spi_pxa2xx_pci: `0' invalid for parameter `gpio_cs'
[ 14.350849] ce4100_spi 0000:00:15.0: enabling device (0000 -> 0002)
[ 14.361603] ce4100_spi 0000:00:15.1: enabling device (0000 -> 0002)
[ 14.382417] spi_master spi0: will run message pump with realtime priority
[ 14.399979] spi_master spi1: will run message pump with realtime priority
[ 14.623098] cfg80211: Calling CRDA to update world regulatory domain
[ 14.651348] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 14.657150] Copyright(c) 2003-2012 Intel Corporation
[ 14.846395] Bluetooth: Core ver 2.16
[ 14.851839] NET: Registered protocol family 31
[ 14.856341] Bluetooth: HCI device and connection manager initialized
[ 14.863849] Bluetooth: HCI socket layer initialized
[ 14.868865] Bluetooth: L2CAP socket layer initialized
[ 14.874350] Bluetooth: SCO socket layer initialized
[ 14.889308] usbcore: registered new interface driver btusb
[ 14.947528] usbcore: registered new interface driver usbhid
[ 14.953285] usbhid: USB HID core driver
Starting Bootlog daemon: bootlogd.
Configuring network interfaces... [ 17.904695] eth0: device MAC address **:**:**:**:**:**
udhcpc (v1.20.2) started
Sending discover...
[ 19.910494] libphy: stmmac-1:01 - Link is Up - 100/Full
Sending discover...
Sending select for 192.168.0.209...
Lease of 192.168.0.209 obtained, lease time 172800
/etc/udhcpc.d/50default: Adding DNS 192.168.0.1
done.
kernel.hotplug = /sbin/mdev
sh: %4Y%2m%2d%2H%2M: bad number
INIT: Entering runlevel: 5
Starting syslogd/klogd: done
Stopping Bootlog daemon: bootlogd.
/sketch/sketch.elf file does not exist or invalid permissions
clloader waiting to receive.
Poky 9.0.2 (Yocto Project 1.4 Reference Distro) 1.4.2 clanton /dev/ttyS1
clanton login: どうやら更新後のイメージにはIntelのWi-Fi・Bluetoothドライバーが含まれているようですね。
/proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 5
model : 9
model name : 05/09
stepping : 0
cpu MHz : 399.088
cache size : 0 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : yes
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 7
wp : yes
flags : fpu vme pse tsc msr pae cx8 apic pge pbe nx smep
bogomips : 798.17
clflush size : 32
cache_alignment : 32
address sizes : 32 bits physical, 32 bits virtual
power management:
「Intel® Quark SoC X1000 Core Developer’s Manual October 2013 Order Number: 329679-001US」の310ページに掲載されている「Table 102. CPUID with PAE/XD/SMEP features implemented (Sheet 2 of 2)」によれば、Intel Quark SoC X1000は、CPUID命令でmodel nameを返さないはずなので、この「05/09」というのはLinuxが別途設定した値かもしれません（深く調べてはいません）。
キャッシュが「0 KB」となっているのも、同様にCPUID命令で情報を返さないことに由来します。
コードネーム「Ivy Bridge」マイクロアーキテクチャで導入された「SMEP（Supervisor Mode Execution Protection – Intel® OS Guardという別名もあり）」をサポートしているのは特筆に値するように思います。
lspci
00:00.0 Class 0600: 8086:0958
00:14.0 Class 0805: 8086:08a7
00:14.1 Class 0700: 8086:0936
00:14.2 Class 0c03: 8086:0939
00:14.3 Class 0c03: 8086:0939
00:14.4 Class 0c03: 8086:093a
00:14.5 Class 0700: 8086:0936
00:14.6 Class 0200: 8086:0937
00:14.7 Class 0200: 8086:0937
00:15.0 Class 0c80: 8086:0935
00:15.1 Class 0c80: 8086:0935
00:15.2 Class 0c80: 8086:0934
00:17.0 Class 0604: 8086:11c3
00:17.1 Class 0604: 8086:11c4
00:1f.0 Class 0601: 8086:095elsusb
Bus 001 Device 001: ID 1d6b:0001
Bus 002 Device 001: ID 1d6b:0002lsmod
Tainted: G
ad7298 12726 0 - Live 0xe082e000
industrialio_triggered_buffer 12686 1 ad7298, Live 0xe0821000
kfifo_buf 13032 1 industrialio_triggered_buffer, Live 0xe0796000
industrialio 43174 3 ad7298,industrialio_triggered_buffer,kfifo_buf, Live 0xe083a000
spi_pxa2xx 21699 0 - Live 0xe0827000
spi_pxa2xx_pci 13472 1 spi_pxa2xx, Live 0xe081c000
spidev 13580 0 - Live 0xe0817000
i2c_dev 13147 0 - Live 0xe0812000
cy8c9540a 13443 0 - Live 0xe07df000
intel_cln_gip 20098 4 - Live 0xe080c000
i2c_core 27485 3 i2c_dev,cy8c9540a,intel_cln_gip, Live 0xe07ba000
gpio_sch 13009 0 - Live 0xe07a6000
usb_storage 46674 0 - Live 0xe07d2000
ohci_hcd 26510 0 - Live 0xe079e000
ehci_hcd 44468 0 - Live 0xe07c6000
usbcore 148859 3 usb_storage,ohci_hcd,ehci_hcd, Live 0xe07e6000
stmmac 52698 0 - Live 0xe07ac000
g_serial 24296 3 - Live 0xe078f000
libcomposite 24078 1 g_serial, Live 0xe0788000
pch_udc 31633 0 - Live 0xe077b000
udc_core 14227 2 libcomposite,pch_udc, Live 0xe076d000
usb_common 12482 3 usbcore,libcomposite,udc_core, Live 0xe0730000
mmc_block 26608 0 - Live 0xe0765000
sdhci_pci 18189 0 - Live 0xe0743000
sdhci 27516 1 sdhci_pci, Live 0xe0737000
mmc_core 93110 3 mmc_block,sdhci_pci,sdhci, Live 0xe074d000
led_class 13338 1 sdhci, Live 0xe0729000
dmesg（ファームウェア更新後）
Ethernetに接続がない状態で起動したログです：
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.7-yocto-standard (clntonsw@irsswdev001) (gcc version 4.7.2 (GCC) ) #1 Tue Oct 1 00:07:32 IST 2013
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000096fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000097000-0x0000000000097fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000098000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000f0defff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000f0df000-0x000000000f11efff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000000f11f000-0x000000000f1defff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000f1df000-0x000000000fedefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000000fedf000-0x000000000feeefff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000feef000-0x000000000feeffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved
[ 0.000000] Early serial console at MMIO32 0x8010f000 (options '115200n8')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.31 by EKI
[ 0.000000] efi: SMBIOS=0xfeee000 ACPI=0xf11e000 ACPI 2.0=0xf11e014
[ 0.000000] efi: mem00: type=7, attr=0xf, range=[0x0000000000000000-0x0000000000095000) (0MB)
[ 0.000000] efi: mem01: type=2, attr=0xf, range=[0x0000000000095000-0x0000000000097000) (0MB)
[ 0.000000] efi: mem02: type=0, attr=0xf, range=[0x0000000000097000-0x0000000000098000) (0MB)
[ 0.000000] efi: mem03: type=7, attr=0xf, range=[0x0000000000098000-0x00000000000a0000) (0MB)
[ 0.000000] efi: mem04: type=2, attr=0xf, range=[0x0000000000100000-0x0000000000301000) (2MB)
[ 0.000000] efi: mem05: type=7, attr=0xf, range=[0x0000000000301000-0x0000000001fde000) (28MB)
[ 0.000000] efi: mem06: type=4, attr=0xf, range=[0x0000000001fde000-0x0000000002000000) (0MB)
[ 0.000000] efi: mem07: type=7, attr=0xf, range=[0x0000000002000000-0x000000000c0e0000) (160MB)
[ 0.000000] efi: mem08: type=4, attr=0xf, range=[0x000000000c0e0000-0x000000000c100000) (0MB)
[ 0.000000] efi: mem09: type=7, attr=0xf, range=[0x000000000c100000-0x000000000dd5f000) (28MB)
[ 0.000000] efi: mem10: type=2, attr=0xf, range=[0x000000000dd5f000-0x000000000e3c4000) (6MB)
[ 0.000000] efi: mem11: type=4, attr=0xf, range=[0x000000000e3c4000-0x000000000e408000) (0MB)
[ 0.000000] efi: mem12: type=2, attr=0xf, range=[0x000000000e408000-0x000000000e40b000) (0MB)
[ 0.000000] efi: mem13: type=1, attr=0xf, range=[0x000000000e40b000-0x000000000e44c000) (0MB)
[ 0.000000] efi: mem14: type=4, attr=0xf, range=[0x000000000e44c000-0x000000000e458000) (0MB)
[ 0.000000] efi: mem15: type=3, attr=0xf, range=[0x000000000e458000-0x000000000e45f000) (0MB)
[ 0.000000] efi: mem16: type=4, attr=0xf, range=[0x000000000e45f000-0x000000000e4b9000) (0MB)
[ 0.000000] efi: mem17: type=3, attr=0xf, range=[0x000000000e4b9000-0x000000000e4c6000) (0MB)
[ 0.000000] efi: mem18: type=4, attr=0xf, range=[0x000000000e4c6000-0x000000000e4c8000) (0MB)
[ 0.000000] efi: mem19: type=3, attr=0xf, range=[0x000000000e4c8000-0x000000000e4ca000) (0MB)
[ 0.000000] efi: mem20: type=4, attr=0xf, range=[0x000000000e4ca000-0x000000000e4cd000) (0MB)
[ 0.000000] efi: mem21: type=3, attr=0xf, range=[0x000000000e4cd000-0x000000000e4d2000) (0MB)
[ 0.000000] efi: mem22: type=4, attr=0xf, range=[0x000000000e4d2000-0x000000000e4d3000) (0MB)
[ 0.000000] efi: mem23: type=3, attr=0xf, range=[0x000000000e4d3000-0x000000000e4e7000) (0MB)
[ 0.000000] efi: mem24: type=4, attr=0xf, range=[0x000000000e4e7000-0x000000000e4e8000) (0MB)
[ 0.000000] efi: mem25: type=3, attr=0xf, range=[0x000000000e4e8000-0x000000000e4ee000) (0MB)
[ 0.000000] efi: mem26: type=4, attr=0xf, range=[0x000000000e4ee000-0x000000000e4ef000) (0MB)
[ 0.000000] efi: mem27: type=3, attr=0xf, range=[0x000000000e4ef000-0x000000000e520000) (0MB)
[ 0.000000] efi: mem28: type=4, attr=0xf, range=[0x000000000e520000-0x000000000e534000) (0MB)
[ 0.000000] efi: mem29: type=3, attr=0xf, range=[0x000000000e534000-0x000000000e539000) (0MB)
[ 0.000000] efi: mem30: type=4, attr=0xf, range=[0x000000000e539000-0x000000000e53a000) (0MB)
[ 0.000000] efi: mem31: type=3, attr=0xf, range=[0x000000000e53a000-0x000000000e54b000) (0MB)
[ 0.000000] efi: mem32: type=4, attr=0xf, range=[0x000000000e54b000-0x000000000e55b000) (0MB)
[ 0.000000] efi: mem33: type=3, attr=0xf, range=[0x000000000e55b000-0x000000000e567000) (0MB)
[ 0.000000] efi: mem34: type=4, attr=0xf, range=[0x000000000e567000-0x000000000e57c000) (0MB)
[ 0.000000] efi: mem35: type=3, attr=0xf, range=[0x000000000e57c000-0x000000000e57e000) (0MB)
[ 0.000000] efi: mem36: type=4, attr=0xf, range=[0x000000000e57e000-0x000000000e5ad000) (0MB)
[ 0.000000] efi: mem37: type=3, attr=0xf, range=[0x000000000e5ad000-0x000000000e5b6000) (0MB)
[ 0.000000] efi: mem38: type=4, attr=0xf, range=[0x000000000e5b6000-0x000000000e5c2000) (0MB)
[ 0.000000] efi: mem39: type=3, attr=0xf, range=[0x000000000e5c2000-0x000000000e5d0000) (0MB)
[ 0.000000] efi: mem40: type=4, attr=0xf, range=[0x000000000e5d0000-0x000000000e5d3000) (0MB)
[ 0.000000] efi: mem41: type=3, attr=0xf, range=[0x000000000e5d3000-0x000000000e5ec000) (0MB)
[ 0.000000] efi: mem42: type=4, attr=0xf, range=[0x000000000e5ec000-0x000000000e710000) (1MB)
[ 0.000000] efi: mem43: type=3, attr=0xf, range=[0x000000000e710000-0x000000000e726000) (0MB)
[ 0.000000] efi: mem44: type=4, attr=0xf, range=[0x000000000e726000-0x000000000e728000) (0MB)
[ 0.000000] efi: mem45: type=3, attr=0xf, range=[0x000000000e728000-0x000000000e72f000) (0MB)
[ 0.000000] efi: mem46: type=4, attr=0xf, range=[0x000000000e72f000-0x000000000e734000) (0MB)
[ 0.000000] efi: mem47: type=3, attr=0xf, range=[0x000000000e734000-0x000000000e735000) (0MB)
[ 0.000000] efi: mem48: type=4, attr=0xf, range=[0x000000000e735000-0x000000000e736000) (0MB)
[ 0.000000] efi: mem49: type=3, attr=0xf, range=[0x000000000e736000-0x000000000e752000) (0MB)
[ 0.000000] efi: mem50: type=4, attr=0xf, range=[0x000000000e752000-0x000000000e753000) (0MB)
[ 0.000000] efi: mem51: type=3, attr=0xf, range=[0x000000000e753000-0x000000000e759000) (0MB)
[ 0.000000] efi: mem52: type=4, attr=0xf, range=[0x000000000e759000-0x000000000e774000) (0MB)
[ 0.000000] efi: mem53: type=3, attr=0xf, range=[0x000000000e774000-0x000000000e776000) (0MB)
[ 0.000000] efi: mem54: type=4, attr=0xf, range=[0x000000000e776000-0x000000000e777000) (0MB)
[ 0.000000] efi: mem55: type=3, attr=0xf, range=[0x000000000e777000-0x000000000e77b000) (0MB)
[ 0.000000] efi: mem56: type=4, attr=0xf, range=[0x000000000e77b000-0x000000000e77c000) (0MB)
[ 0.000000] efi: mem57: type=3, attr=0xf, range=[0x000000000e77c000-0x000000000e785000) (0MB)
[ 0.000000] efi: mem58: type=4, attr=0xf, range=[0x000000000e785000-0x000000000e789000) (0MB)
[ 0.000000] efi: mem59: type=3, attr=0xf, range=[0x000000000e789000-0x000000000e78d000) (0MB)
[ 0.000000] efi: mem60: type=4, attr=0xf, range=[0x000000000e78d000-0x000000000e79f000) (0MB)
[ 0.000000] efi: mem61: type=3, attr=0xf, range=[0x000000000e79f000-0x000000000e7a1000) (0MB)
[ 0.000000] efi: mem62: type=4, attr=0xf, range=[0x000000000e7a1000-0x000000000e7a9000) (0MB)
[ 0.000000] efi: mem63: type=3, attr=0xf, range=[0x000000000e7a9000-0x000000000e7af000) (0MB)
[ 0.000000] efi: mem64: type=4, attr=0xf, range=[0x000000000e7af000-0x000000000e7b7000) (0MB)
[ 0.000000] efi: mem65: type=3, attr=0xf, range=[0x000000000e7b7000-0x000000000e7bb000) (0MB)
[ 0.000000] efi: mem66: type=4, attr=0xf, range=[0x000000000e7bb000-0x000000000e7cc000) (0MB)
[ 0.000000] efi: mem67: type=3, attr=0xf, range=[0x000000000e7cc000-0x000000000e7d1000) (0MB)
[ 0.000000] efi: mem68: type=4, attr=0xf, range=[0x000000000e7d1000-0x000000000f0df000) (9MB)
[ 0.000000] efi: mem69: type=9, attr=0xf, range=[0x000000000f0df000-0x000000000f11f000) (0MB)
[ 0.000000] efi: mem70: type=5, attr=0x800000000000000f, range=[0x000000000f11f000-0x000000000f17f000) (0MB)
[ 0.000000] efi: mem71: type=6, attr=0x800000000000000f, range=[0x000000000f17f000-0x000000000f1df000) (0MB)
[ 0.000000] efi: mem72: type=10, attr=0xf, range=[0x000000000f1df000-0x000000000fedf000) (13MB)
[ 0.000000] efi: mem73: type=0, attr=0xf, range=[0x000000000fedf000-0x000000000feef000) (0MB)
[ 0.000000] efi: mem74: type=4, attr=0xf, range=[0x000000000feef000-0x000000000fef0000) (0MB)
[ 0.000000] efi: mem75: type=11, attr=0x8000000000000000, range=[0x00000000e0000000-0x00000000f0000000) (256MB)
[ 0.000000] efi: mem76: type=11, attr=0x8000000000000000, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
[ 0.000000] efi: mem77: type=11, attr=0x8000000000000001, range=[0x00000000ff800000-0x0000000100000000) (8MB)
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0xfef0 max_arch_pfn = 0x1000000
[ 0.000000] Scan for SMP in [mem 0x00000000-0x000003ff]
[ 0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff]
[ 0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff]
[ 0.000000] Scan for SMP in [mem 0x000aaaa0-0x000aae9f]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01ffffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x0feeffff]
[ 0.000000] [mem 0x00000000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x0fdfffff] page 2M
[ 0.000000] [mem 0x0fe00000-0x0feeffff] page 4k
[ 0.000000] kernel direct mapping tables up to 0xfeeffff @ [mem 0x01fd8000-0x01fddfff]
[ 0.000000] RAMDISK: [mem 0x0dd5f000-0x0dfc3fff]
[ 0.000000] ACPI: RSDP 0f11e014 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 0f11d0e8 0006C (v01 INTEL TIANO 00000003 01000013)
[ 0.000000] ACPI: FACP 0f11b000 000F4 (v03 INTEL TIANO 00000003 INTL 0100000D)
[ 0.000000] ACPI: DSDT 0f113000 015A2 (v01 INTEL ClantonN 00000003 INTL 20081031)
[ 0.000000] ACPI: FACS 0f2c7000 00040
[ 0.000000] ACPI: UEFI 0fcd5000 00042 (v01 00000000 00000000)
[ 0.000000] ACPI: APIC 0f11c000 0005A (v01 INTEL TIANO 00000001 MSFT 00000000)
[ 0.000000] ACPI: HPET 0f11a000 00038 (v01 00000001 00000000)
[ 0.000000] ACPI: MCFG 0f119000 0003C (v01 00000001 00000000)
[ 0.000000] ACPI: SSDT 0f118000 004D8 (v01 SsgPmm Cpu0Cst 00000011 INTL 20081031)
[ 0.000000] ACPI: SSDT 0f117000 0043F (v01 SsgPmm Cpu0Ist 00000012 INTL 20081031)
[ 0.000000] ACPI: SSDT 0f116000 0013B (v01 SsgPmm Cpu0Tst 00000013 INTL 20081031)
[ 0.000000] ACPI: SSDT 0f115000 00056 (v01 SsgPmm CpuPm 00000010 INTL 20081031)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffffb000 ( fee00000)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 254MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0fef0000
[ 0.000000] low ram: 0 - 0fef0000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00010000-0x0feeffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x00096fff]
[ 0.000000] node 0: [mem 0x00098000-0x0009ffff]
[ 0.000000] node 0: [mem 0x00100000-0x0f0defff]
[ 0.000000] node 0: [mem 0x0feef000-0x0feeffff]
[ 0.000000] On node 0 totalpages: 61551
[ 0.000000] free_area_init_node: node 0, pgdat c1484720, node_mem_map ce1c4200
[ 0.000000] Normal zone: 510 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 61041 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffffb000 ( fee00000)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: Assigned apic_id 1
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 1, APIC INT 02
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 1, APIC INT 09
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 1, APIC INT 01
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 1, APIC INT 03
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 1, APIC INT 04
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 1, APIC INT 05
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 1, APIC INT 06
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 1, APIC INT 07
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 1, APIC INT 08
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 1, APIC INT 0a
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 1, APIC INT 0b
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 1, APIC INT 0c
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 1, APIC INT 0d
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 1, APIC INT 0e
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 1, APIC INT 0f
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] e820: [mem 0x0fef0000-0xdfffffff] available for PCI devices
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61041
[ 0.000000] Kernel command line: root=/dev/ram0 console=ttyS1,115200n8 earlycon=uart8250,mmio32,0x8010f000,115200n8 reboot=efi,warm apic=debug rw efi_main=0x00000001423482b5 jmp_code32=0x0000000298b06b5d
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 217672k/261056k available (3098k kernel code, 28532k reserved, 1547k data, 272k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa2000 - 0xfffff000 ( 372 kB)
[ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xd06f0000 - 0xffbfe000 ( 757 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcfef0000 ( 254 MB)
[ 0.000000] .init : 0xc148a000 - 0xc14ce000 ( 272 kB)
[ 0.000000] .data : 0xc1306812 - 0xc1489480 (1547 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1306812 (3098 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[ 0.000000] CPU 0 irqstacks, hard=c0090000 soft=c0092000
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3567 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] tsc: Detected 399.076 MHz processor
[ 0.010015] Calibrating delay loop (skipped), value calculated using timer frequency.. 798.15 BogoMIPS (lpj=3990760)
[ 0.010136] pid_max: default: 32768 minimum: 301
[ 0.408280] Security Framework initialized
[ 0.408553] Mount-cache hash table entries: 512
[ 0.417685] Initializing cgroup subsys cpuacct
[ 0.417855] Initializing cgroup subsys freezer
[ 0.418657] Intel Pentium with F0 0F bug - workaround enabled.
[ 0.418916] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.418916] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.418916] tlb_flushall_shift: 6
[ 0.419060] CPU: Intel 05/09 (fam: 05, model: 09, stepping: 00)
[ 0.419295] ACPI: Core revision 20121018
[ 0.505025] Performance Events: no PMU driver, software events only.
[ 0.509939] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.510081] Getting VERSION: 30010
[ 0.510146] Getting VERSION: 30010
[ 0.510199] Getting ID: 0
[ 0.510248] Getting ID: f000000
[ 0.510300] Getting LVT0: 700
[ 0.510350] Getting LVT1: 400
[ 0.510419] enabled ExtINT on CPU#0
[ 0.510832] ENABLING IO-APIC IRQs
[ 0.510887] Synchronizing Arb IDs.
[ 0.510937] init IO_APIC IRQs
[ 0.510969] apic 1 pin 0 not connected
[ 0.511334] IOAPIC[0]: Set routing entry (1-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1)
[ 0.511456] IOAPIC[0]: Set routing entry (1-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1)
[ 0.511566] IOAPIC[0]: Set routing entry (1-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1)
[ 0.511675] IOAPIC[0]: Set routing entry (1-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1)
[ 0.511786] IOAPIC[0]: Set routing entry (1-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:1)
[ 0.511896] IOAPIC[0]: Set routing entry (1-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1)
[ 0.512005] IOAPIC[0]: Set routing entry (1-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1)
[ 0.512115] IOAPIC[0]: Set routing entry (1-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[ 0.512223] IOAPIC[0]: Set routing entry (1-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1)
[ 0.512332] IOAPIC[0]: Set routing entry (1-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:1)
[ 0.512442] IOAPIC[0]: Set routing entry (1-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:1)
[ 0.512551] IOAPIC[0]: Set routing entry (1-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1)
[ 0.512661] IOAPIC[0]: Set routing entry (1-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:1)
[ 0.512771] IOAPIC[0]: Set routing entry (1-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:1)
[ 0.512882] IOAPIC[0]: Set routing entry (1-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:1)
[ 0.512960] apic 1 pin 16 not connected
[ 0.512996] apic 1 pin 17 not connected
[ 0.513026] apic 1 pin 18 not connected
[ 0.513053] apic 1 pin 19 not connected
[ 0.513081] apic 1 pin 20 not connected
[ 0.513107] apic 1 pin 21 not connected
[ 0.513136] apic 1 pin 22 not connected
[ 0.513163] apic 1 pin 23 not connected
[ 0.513352] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.613569] Using local APIC timer interrupts.
[ 0.613569] calibrating APIC timer ...
[ 0.620000] ... lapic delta = 2494196
[ 0.620000] ... PM-Timer delta = 357950
[ 0.620000] ... PM-Timer result ok
[ 0.620000] ..... delta 2494196
[ 0.620000] ..... mult: 107124902
[ 0.620000] ..... calibration result: 3990713
[ 0.620000] ..... CPU clock speed is 399.0713 MHz.
[ 0.620000] ..... host bus clock speed is 399.0713 MHz.
[ 0.620000] devtmpfs: initialized
[ 0.623083] PM: Registering ACPI NVS region [mem 0x0f1df000-0x0fedefff] (13631488 bytes)
[ 0.629131] RTC time: 21:59:25, date: 12/27/13
[ 0.631893] NET: Registered protocol family 16
[ 0.657742] ACPI: bus type pci registered
[ 0.660096] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.660217] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.660297] PCI: Using MMCONFIG for extended config space
[ 0.660367] PCI: Using configuration type 1 for base access
[ 0.809719] bio: create slab at 0
[ 0.814425] ACPI: Added _OSI(Module Device)
[ 0.814519] ACPI: Added _OSI(Processor Device)
[ 0.814601] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.814686] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.834445] ACPI: EC: Look up EC in DSDT
[ 0.897688] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.905883] ACPI: Interpreter enabled
[ 0.905949] ACPI: (supports S0 S3 S5)
[ 0.906776] ACPI: Using IOAPIC for interrupt routing
[ 1.070847] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.076477] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 1.076641] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.096803] PCI host bridge to bus 0000:00
[ 1.096922] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.097020] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 1.097116] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 1.097213] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 1.097315] pci_bus 0000:00: root bus resource [mem 0x10000000-0xfebfffff]
[ 1.097578] pci_bus 0000:00: scanning bus
[ 1.098293] pci 0000:00:00.0: [8086:0958] type 00 class 0x060000
[ 1.098420] pci 0000:00:00.0: calling quirk_mmio_always_on+0x0/0x10
[ 1.099913] pci 0000:00:14.0: [8086:08a7] type 00 class 0x080501
[ 1.100220] pci 0000:00:14.0: reg 10: [mem 0x90010000-0x90010fff]
[ 1.100875] pci 0000:00:14.0: PME# supported from D0 D3hot
[ 1.101779] pci 0000:00:14.0: PME# disabled
[ 1.102051] pci 0000:00:14.1: [8086:0936] type 00 class 0x070002
[ 1.102239] pci 0000:00:14.1: reg 10: [mem 0x9000f000-0x9000ffff]
[ 1.102360] pci 0000:00:14.1: reg 14: [mem 0x9000e000-0x9000efff]
[ 1.102961] pci 0000:00:14.1: PME# supported from D0 D3hot
[ 1.103051] pci 0000:00:14.1: PME# disabled
[ 1.103308] pci 0000:00:14.2: [8086:0939] type 00 class 0x0c03fe
[ 1.103493] pci 0000:00:14.2: reg 10: [mem 0x90004000-0x90005fff]
[ 1.104143] pci 0000:00:14.2: PME# supported from D0 D3hot
[ 1.104233] pci 0000:00:14.2: PME# disabled
[ 1.104505] pci 0000:00:14.3: [8086:0939] type 00 class 0x0c0320
[ 1.104705] pci 0000:00:14.3: reg 10: [mem 0x9000d000-0x9000dfff]
[ 1.105396] pci 0000:00:14.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.105487] pci 0000:00:14.3: PME# disabled
[ 1.105757] pci 0000:00:14.4: [8086:093a] type 00 class 0x0c0310
[ 1.105944] pci 0000:00:14.4: reg 10: [mem 0x9000c000-0x9000cfff]
[ 1.106594] pci 0000:00:14.4: PME# supported from D0 D3hot
[ 1.106683] pci 0000:00:14.4: PME# disabled
[ 1.106943] pci 0000:00:14.5: [8086:0936] type 00 class 0x070002
[ 1.107130] pci 0000:00:14.5: reg 10: [mem 0x9000b000-0x9000bfff]
[ 1.107251] pci 0000:00:14.5: reg 14: [mem 0x9000a000-0x9000afff]
[ 1.107853] pci 0000:00:14.5: PME# supported from D0 D3hot
[ 1.107943] pci 0000:00:14.5: PME# disabled
[ 1.108201] pci 0000:00:14.6: [8086:0937] type 00 class 0x020000
[ 1.108387] pci 0000:00:14.6: reg 10: [mem 0x90002000-0x90003fff]
[ 1.109037] pci 0000:00:14.6: PME# supported from D0 D3hot
[ 1.109126] pci 0000:00:14.6: PME# disabled
[ 1.109423] pci 0000:00:14.7: [8086:0937] type 00 class 0x020000
[ 1.109612] pci 0000:00:14.7: reg 10: [mem 0x90000000-0x90001fff]
[ 1.110364] pci 0000:00:14.7: PME# supported from D0 D3hot
[ 1.110457] pci 0000:00:14.7: PME# disabled
[ 1.110719] pci 0000:00:15.0: [8086:0935] type 00 class 0x0c8000
[ 1.110906] pci 0000:00:15.0: reg 10: [mem 0x90009000-0x90009fff]
[ 1.111555] pci 0000:00:15.0: PME# supported from D0 D3hot
[ 1.111644] pci 0000:00:15.0: PME# disabled
[ 1.111905] pci 0000:00:15.1: [8086:0935] type 00 class 0x0c8000
[ 1.112092] pci 0000:00:15.1: reg 10: [mem 0x90008000-0x90008fff]
[ 1.112742] pci 0000:00:15.1: PME# supported from D0 D3hot
[ 1.112832] pci 0000:00:15.1: PME# disabled
[ 1.113090] pci 0000:00:15.2: [8086:0934] type 00 class 0x0c8000
[ 1.113276] pci 0000:00:15.2: reg 10: [mem 0x90007000-0x90007fff]
[ 1.113395] pci 0000:00:15.2: reg 14: [mem 0x90006000-0x90006fff]
[ 1.113994] pci 0000:00:15.2: PME# supported from D0 D3hot
[ 1.114084] pci 0000:00:15.2: PME# disabled
[ 1.114404] pci 0000:00:17.0: [8086:11c3] type 01 class 0x060400
[ 1.114804] pci 0000:00:17.0: calling pci_fixup_transparent_bridge+0x0/0x30
[ 1.115188] pci 0000:00:17.0: PME# supported from D0 D3hot D3cold
[ 1.115274] pci 0000:00:17.0: PME# disabled
[ 1.115557] pci 0000:00:17.1: [8086:11c4] type 01 class 0x060400
[ 1.115952] pci 0000:00:17.1: calling pci_fixup_transparent_bridge+0x0/0x30
[ 1.116336] pci 0000:00:17.1: PME# supported from D0 D3hot D3cold
[ 1.116423] pci 0000:00:17.1: PME# disabled
[ 1.116822] pci 0000:00:1f.0: [8086:095e] type 00 class 0x060100
[ 1.117387] pci_bus 0000:00: fixups for bus
[ 1.117469] pci 0000:00:17.0: scanning [bus 01-01] behind bridge, pass 0
[ 1.117850] pci_bus 0000:01: scanning bus
[ 1.117925] pci_bus 0000:01: fixups for bus
[ 1.117979] pci 0000:00:17.0: PCI bridge to [bus 01]
[ 1.118130] pci_bus 0000:01: bus scan returning with max=01
[ 1.118213] pci 0000:00:17.1: scanning [bus 02-02] behind bridge, pass 0
[ 1.118629] pci_bus 0000:02: scanning bus
[ 1.118705] pci_bus 0000:02: fixups for bus
[ 1.118758] pci 0000:00:17.1: PCI bridge to [bus 02]
[ 1.118908] pci_bus 0000:02: bus scan returning with max=02
[ 1.118995] pci 0000:00:17.0: scanning [bus 01-01] behind bridge, pass 1
[ 1.119085] pci 0000:00:17.1: scanning [bus 02-02] behind bridge, pass 1
[ 1.119163] pci_bus 0000:00: bus scan returning with max=02
[ 1.119212] pci_bus 0000:00: on NUMA node 0
[ 1.120283] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 1.122829] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[ 1.128988] pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 1.129094] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 1.195317] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.199271] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.203936] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.207882] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.211942] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.215896] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.219891] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.223954] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.235439] vgaarb: loaded
[ 1.240998] SCSI subsystem initialized
[ 1.253205] PCI: Using ACPI for IRQ routing
[ 1.282099] PCI: pci_cache_line_size set to 32 bytes
[ 1.282253] pci 0000:00:14.0: BAR 0: reserving [mem 0x90010000-0x90010fff flags 0x40200] (d=0, p=0)
[ 1.282364] pci 0000:00:14.1: BAR 0: reserving [mem 0x9000f000-0x9000ffff flags 0x40200] (d=0, p=0)
[ 1.282442] pci 0000:00:14.1: BAR 1: reserving [mem 0x9000e000-0x9000efff flags 0x40200] (d=0, p=0)
[ 1.282542] pci 0000:00:14.2: BAR 0: reserving [mem 0x90004000-0x90005fff flags 0x40200] (d=0, p=0)
[ 1.282647] pci 0000:00:14.3: BAR 0: reserving [mem 0x9000d000-0x9000dfff flags 0x40200] (d=0, p=0)
[ 1.282751] pci 0000:00:14.4: BAR 0: reserving [mem 0x9000c000-0x9000cfff flags 0x40200] (d=0, p=0)
[ 1.282855] pci 0000:00:14.5: BAR 0: reserving [mem 0x9000b000-0x9000bfff flags 0x40200] (d=0, p=0)
[ 1.282933] pci 0000:00:14.5: BAR 1: reserving [mem 0x9000a000-0x9000afff flags 0x40200] (d=0, p=0)
[ 1.283093] pci 0000:00:15.2: BAR 0: reserving [mem 0x90007000-0x90007fff flags 0x40200] (d=0, p=0)
[ 1.283171] pci 0000:00:15.2: BAR 1: reserving [mem 0x90006000-0x90006fff flags 0x40200] (d=0, p=0)
[ 1.283422] pci 0000:00:14.6: BAR 0: reserving [mem 0x90002000-0x90003fff flags 0x40200] (d=1, p=1)
[ 1.283527] pci 0000:00:14.7: BAR 0: reserving [mem 0x90000000-0x90001fff flags 0x40200] (d=1, p=1)
[ 1.283631] pci 0000:00:15.0: BAR 0: reserving [mem 0x90009000-0x90009fff flags 0x40200] (d=1, p=1)
[ 1.283736] pci 0000:00:15.1: BAR 0: reserving [mem 0x90008000-0x90008fff flags 0x40200] (d=1, p=1)
[ 1.283898] e820: reserve RAM buffer [mem 0x00097000-0x0009ffff]
[ 1.283959] e820: reserve RAM buffer [mem 0x0f0df000-0x0fffffff]
[ 1.284015] e820: reserve RAM buffer [mem 0x0fef0000-0x0fffffff]
[ 1.293713] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 1.293827] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 1.293938] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 1.297883] Switching to clocksource hpet
[ 1.297883] pnp: PnP ACPI init
[ 1.297883] ACPI: bus type pnp registered
[ 1.302090] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 1.302226] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.302348] system 00:00: [mem 0x000c0000-0x000dffff] has been reserved
[ 1.302478] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
[ 1.302605] system 00:00: [mem 0xff800000-0xffffffff] has been reserved
[ 1.303163] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.315557] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.318289] pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
[ 1.332368] system 00:03: [io 0x1000-0x100f] has been reserved
[ 1.332496] system 00:03: [io 0x1010-0x101f] has been reserved
[ 1.332616] system 00:03: [io 0x1100-0x113f] has been reserved
[ 1.332736] system 00:03: [io 0x1080-0x10bf] has been reserved
[ 1.332858] system 00:03: [io 0x1040-0x107f] has been reserved
[ 1.332980] system 00:03: [io 0x1020-0x103f] has been reserved
[ 1.333103] system 00:03: [io 0x1140-0x117f] has been reserved
[ 1.333267] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.336802] IOAPIC[0]: Set routing entry (1-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[ 1.339220] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.343420] pnp 00:05: Plug and Play ACPI device, IDs PNP0003 (active)
[ 1.343679] pnp: PnP ACPI: found 6 devices
[ 1.343757] ACPI: ACPI bus type pnp unregistered
[ 1.560766] pci 0000:00:17.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 1.560854] pci 0000:00:17.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 1.560926] pci 0000:00:17.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[ 1.561057] pci 0000:00:17.1: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
[ 1.561134] pci 0000:00:17.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[ 1.561205] pci 0000:00:17.1: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
[ 1.561337] pci 0000:00:17.0: res[8]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 1.561400] pci 0000:00:17.0: res[9]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 1.561457] pci 0000:00:17.1: res[8]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 1.561516] pci 0000:00:17.1: res[9]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 1.561573] pci 0000:00:17.0: res[7]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 1.561629] pci 0000:00:17.1: res[7]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 1.561723] pci 0000:00:17.0: BAR 8: assigned [mem 0x10000000-0x101fffff]
[ 1.561863] pci 0000:00:17.0: BAR 9: assigned [mem 0x10200000-0x103fffff 64bit pref]
[ 1.562004] pci 0000:00:17.1: BAR 8: assigned [mem 0x10400000-0x105fffff]
[ 1.562141] pci 0000:00:17.1: BAR 9: assigned [mem 0x10600000-0x107fffff 64bit pref]
[ 1.562288] pci 0000:00:17.0: BAR 7: assigned [io 0x2000-0x2fff]
[ 1.562423] pci 0000:00:17.1: BAR 7: assigned [io 0x3000-0x3fff]
[ 1.562556] pci 0000:00:17.0: PCI bridge to [bus 01]
[ 1.562667] pci 0000:00:17.0: bridge window [io 0x2000-0x2fff]
[ 1.562796] pci 0000:00:17.0: bridge window [mem 0x10000000-0x101fffff]
[ 1.562924] pci 0000:00:17.0: bridge window [mem 0x10200000-0x103fffff 64bit pref]
[ 1.563068] pci 0000:00:17.1: PCI bridge to [bus 02]
[ 1.563175] pci 0000:00:17.1: bridge window [io 0x3000-0x3fff]
[ 1.563303] pci 0000:00:17.1: bridge window [mem 0x10400000-0x105fffff]
[ 1.563430] pci 0000:00:17.1: bridge window [mem 0x10600000-0x107fffff 64bit pref]
[ 1.563706] IOAPIC[0]: Set routing entry (1-20 -> 0x41 -> IRQ 20 Mode:1 Active:1 Dest:1)
[ 1.563934] IOAPIC[0]: Set routing entry (1-21 -> 0x51 -> IRQ 21 Mode:1 Active:1 Dest:1)
[ 1.564062] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.564119] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.564171] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.564225] pci_bus 0000:00: resource 7 [mem 0x10000000-0xfebfffff]
[ 1.564281] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 1.564334] pci_bus 0000:01: resource 1 [mem 0x10000000-0x101fffff]
[ 1.564391] pci_bus 0000:01: resource 2 [mem 0x10200000-0x103fffff 64bit pref]
[ 1.564445] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
[ 1.564498] pci_bus 0000:02: resource 1 [mem 0x10400000-0x105fffff]
[ 1.564552] pci_bus 0000:02: resource 2 [mem 0x10600000-0x107fffff 64bit pref]
[ 1.565521] NET: Registered protocol family 2
[ 1.570279] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 1.570882] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
[ 1.573163] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.573814] TCP: reno registered
[ 1.573937] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 1.574621] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 1.576951] NET: Registered protocol family 1
[ 1.577346] pci 0000:00:14.2: calling quirk_usb_early_handoff+0x0/0x670
[ 1.577477] pci 0000:00:14.3: calling quirk_usb_early_handoff+0x0/0x670
[ 1.577670] IOAPIC[0]: Set routing entry (1-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:1)
[ 1.578107] pci 0000:00:14.4: calling quirk_usb_early_handoff+0x0/0x670
[ 1.578326] IOAPIC[0]: Set routing entry (1-16 -> 0x71 -> IRQ 16 Mode:1 Active:1 Dest:1)
[ 1.578662] pci 0000:00:14.6: calling quirk_e100_interrupt+0x0/0x1b0
[ 1.578801] pci 0000:00:14.7: calling quirk_e100_interrupt+0x0/0x1b0
[ 1.579055] PCI: CLS 0 bytes, default 32
[ 1.581682] Trying to unpack rootfs image as initramfs...
[ 11.540602] Freeing initrd memory: 2452k freed
[ 11.565591] microcode: Intel CPU family 0x5 not supported
[ 11.572322] resource map sanity check conflict: 0xfff00000 0x1002fffff 0xff800000 0xffffffff reserved
[ 11.572436] ------------[ cut here ]------------
[ 11.572554] WARNING: at /build/clntonsw/slave_magnum/meta-cln_spi/build/compile/yocto_build/tmp/work/clanton-poky-linux-uclibc/linux-yocto-clanton/3.8-r0/linux/arch/x86/mm/ioremap.c:171 __ioremap_caller+0x27a/0x440()
[ 11.572717] Info: mapping multiple BARs. Your kernel is fine.
[ 11.572780] Modules linked in:
[ 11.572869] Pid: 1, comm: swapper Not tainted 3.8.7-yocto-standard #1
[ 11.572940] Call Trace:
[ 11.573041] [] warn_slowpath_common+0x5f/0x80
[ 11.573156] [] ? __ioremap_caller+0x27a/0x440
[ 11.573266] [] ? __ioremap_caller+0x27a/0x440
[ 11.573380] [] warn_slowpath_fmt+0x2e/0x30
[ 11.573491] [] __ioremap_caller+0x27a/0x440
[ 11.573608] [] ? intel_cln_board_data_init+0x1a/0x19d
[ 11.573717] [] ? efi_capsule_update_init+0x8d/0x8d
[ 11.573829] [] ioremap_nocache+0x1a/0x20
[ 11.573937] [] ? intel_cln_board_data_init+0x1a/0x19d
[ 11.574046] [] intel_cln_board_data_init+0x1a/0x19d
[ 11.574147] [] ? sysfs_add_file+0x13/0x20
[ 11.574237] [] ? sysfs_create_file+0x1c/0x20
[ 11.574340] [] ? efi_capsule_update_init+0x8d/0x8d
[ 11.574439] [] do_one_initcall+0x10a/0x150
[ 11.574534] [] kernel_init_freeable+0x106/0x1a0
[ 11.574628] [] ? do_early_param+0x7a/0x7a
[ 11.574734] [] kernel_init+0xb/0xd0
[ 11.574833] [] ret_from_kernel_thread+0x1b/0x30
[ 11.574940] [] ? rest_init+0xb0/0xb0
[ 11.575092] ---[ end trace 604253a11828188f ]---
[ 11.575188] MFH: mfh @ 0xe1008000: id 0x5f4d4648 ver 0x00000001 entries 0x0000000a
[ 11.577298] MFH: Warning platform data MFH missing - using hardcoded offsets
[ 11.582940] resource map sanity check conflict: 0xfff10000 0x100000075 0xff800000 0xffffffff reserved
[ 11.583206] CLN-PLT: Clanton Platform ID = 6
[ 11.606666] Intel Clanton side-band driver registered
[ 11.611645] IMR setup complete
[ 11.613968] eSRAM CTRL 0x047f3f91 block 0x00000000
[ 11.614042] eSRAM pages 128
[ 11.635499] intel_cln_esram_test_probe/Oct 1 2013/00:06:41 complete OK !!
[ 11.654649] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 11.797713] msgmni has been set to 456
[ 11.810771] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 11.811158] io scheduler noop registered
[ 11.811242] io scheduler deadline registered
[ 11.811460] io scheduler cfq registered (default)
[ 11.855854] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 11.856741] ACPI: Sleep Button [SLPB]
[ 11.859428] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 11.859608] ACPI: Power Button [PWRB]
[ 12.028236] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 12.041669] IOAPIC[0]: Set routing entry (1-17 -> 0x81 -> IRQ 17 Mode:1 Active:1 Dest:1)
[ 12.042133] Setup PCI port: port 0, irq 17, type 2
[ 12.089918] 0000:00:14.1: ttyS0 at MMIO 0x9000f000 (irq = 17) is a 16550A
[ 12.094385] Setup PCI port: port 0, irq 17, type 2
[ 12.118232] 0000:00:14.5: ttyS1 at MMIO 0x9000b000 (irq = 17) is a 16550A
[ 12.119462] console [ttyS1] enabled, bootconsole disabled
[ 12.132522] Real Time Clock Driver v1.12b
[ 12.149913] brd: module loaded
[ 12.168863] loop: module loaded
[ 12.174459] lpc_sch_probe BIOS_CNTL 0x00000101
[ 12.178980] lpc_sch_probe new BIOS_CNTL 0x00000101
[ 12.183967] lpc_sch_probe RCBA @ 0xfed1c000
[ 12.212152] cpuidle: using governor ladder
[ 12.216322] cpuidle: using governor menu
[ 12.221984] sdhci: Secure Digital Host Controller Interface driver
[ 12.228219] sdhci: Copyright(c) Pierre Ossman
[ 12.233315] sdhci-pci 0000:00:14.0: SDHCI controller found [8086:08a7] (rev 10)
[ 12.243171] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 12.244496] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 12.290253] mmc0: SDHCI controller on PCI [0000:00:14.0] using ADMA
[ 12.303354] sdhci-pltfm: SDHCI platform and OF driver helper
[ 12.334315] THRM: critical reset 104 c hot 95 c hardware failover 105 c
[ 12.361647] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 12.365161] TCP: cubic registered
[ 12.369084] NET: Registered protocol family 17
[ 12.374458]
[ 12.374458] printing PIC contents
[ 12.374518] ... PIC IMR: ffff
[ 12.374548] ... PIC IRR: 0000
[ 12.374576] ... PIC ISR: 0000
[ 12.374605] ... PIC ELCR: 0000
[ 12.374638] printing local APIC contents on CPU#0/0:
[ 12.374670] ... APIC ID: 00000000 (0)
[ 12.378806] ... APIC VERSION: 00030010
[ 12.382593] ... APIC TASKPRI: 00000000 (00)
[ 12.382625] ... APIC ARBPRI: 00000000 (00)
[ 12.382651] ... APIC PROCPRI: 00000000
[ 12.382678] ... APIC RRR: 00000000
[ 12.382705] ... APIC LDR: 01000000
[ 12.382733] ... APIC DFR: ffffffff
[ 12.382763] ... APIC SPIV: 000001ff
[ 12.382788] ... APIC ISR field:
[ 12.382819] 0000000000000000000000000000000000000000000000000000000000000000
[ 12.383629] ... APIC TMR field:
[ 12.383629] 0000000000000000000000000000000000000000000000000000000000000000
[ 12.383629] ... APIC IRR field:
[ 12.383629] 0000000000000000000000000000000000000000000000000000000000008000
[ 12.383629] ... APIC ESR: 00000000
[ 12.383629] ... APIC ICR: 00088500
[ 12.383629] ... APIC ICR2: 00000000
[ 12.383629] ... APIC LVTT: 000000ef
[ 12.383629] ... APIC LVT0: 00010700
[ 12.383629] ... APIC LVT1: 00000400
[ 12.383629] ... APIC LVTERR: 000000fe
[ 12.383629] ... APIC TMICT: 000269a7
[ 12.383629] ... APIC TMCCT: 00000000
[ 12.383629] ... APIC TDCR: 00000003
[ 12.383629]
[ 12.406584] number of MP IRQ sources: 15.
[ 12.406628] number of IO-APIC #1 registers: 24.
[ 12.406655] testing the IO APIC.......................
[ 12.411952] IO APIC #1......
[ 12.411992] .... register #00: 01000000
[ 12.412021] ....... : physical APIC id: 01
[ 12.412047] ....... : Delivery Type: 0
[ 12.412074] ....... : LTS : 0
[ 12.412099] .... register #01: 00170020
[ 12.412127] ....... : max redirection entries: 17
[ 12.412155] ....... : PRQ implemented: 0
[ 12.412180] ....... : IO APIC version: 20
[ 12.412206] .... IRQ redirection table:
[ 12.412231] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
[ 12.412265] 00 00 1 0 0 0 0 0 0 00
[ 12.412322] 01 01 0 0 0 0 0 1 1 31
[ 12.412376] 02 01 0 0 0 0 0 1 1 30
[ 12.412430] 03 01 0 0 0 0 0 1 1 33
[ 12.412483] 04 01 0 0 0 0 0 1 1 34
[ 12.412537] 05 01 0 0 0 0 0 1 1 35
[ 12.412590] 06 01 0 0 0 0 0 1 1 36
[ 12.412644] 07 01 0 0 0 0 0 1 1 37
[ 12.412698] 08 01 0 0 0 0 0 1 1 38
[ 12.412751] 09 01 0 1 0 0 0 1 1 39
[ 12.412805] 0a 01 0 0 0 0 0 1 1 3A
[ 12.412858] 0b 01 0 0 0 0 0 1 1 3B
[ 12.412912] 0c 01 0 0 0 0 0 1 1 3C
[ 12.412965] 0d 01 0 0 0 0 0 1 1 3D
[ 12.413019] 0e 01 0 0 0 0 0 1 1 3E
[ 12.413072] 0f 01 0 0 0 0 0 1 1 3F
[ 12.413126] 10 01 0 1 0 1 0 1 1 71
[ 12.413180] 11 01 1 1 0 1 0 1 1 81
[ 12.413234] 12 00 1 0 0 0 0 0 0 00
[ 12.413288] 13 01 1 1 0 1 0 1 1 61
[ 12.413342] 14 01 1 1 0 1 0 1 1 41
[ 12.413396] 15 01 1 1 0 1 0 1 1 51
[ 12.413450] 16 00 1 0 0 0 0 0 0 00
[ 12.413504] 17 00 1 0 0 0 0 0 0 00
[ 12.413548] IRQ to pin mappings:
[ 12.413580] IRQ0 -> 0:2
[ 12.413620] IRQ1 -> 0:1
[ 12.413659] IRQ3 -> 0:3
[ 12.413700] IRQ4 -> 0:4
[ 12.413739] IRQ5 -> 0:5
[ 12.413779] IRQ6 -> 0:6
[ 12.413818] IRQ7 -> 0:7
[ 12.413858] IRQ8 -> 0:8
[ 12.413897] IRQ9 -> 0:9
[ 12.413937] IRQ10 -> 0:10
[ 12.413977] IRQ11 -> 0:11
[ 12.414018] IRQ12 -> 0:12
[ 12.414057] IRQ13 -> 0:13
[ 12.414098] IRQ14 -> 0:14
[ 12.414137] IRQ15 -> 0:15
[ 12.414179] IRQ16 -> 0:16
[ 12.414218] IRQ17 -> 0:17
[ 12.414259] IRQ19 -> 0:19
[ 12.414299] IRQ20 -> 0:20
[ 12.414339] IRQ21 -> 0:21
[ 12.414378] .................................... done.
[ 12.419560] Using IPI Shortcut mode
[ 12.438633] Magic number: 9:737:1006
[ 12.466699] Freeing unused kernel memory: 272k freed
[ 12.492221] Write protecting the kernel text: 3100k
[ 12.498272] Write protecting the kernel read-only data: 1284k
[ 12.504196] NX-protecting the kernel data: 3044k
[ 12.513852] Failed to execute /init
[ 12.534789] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 12.550719] tsc: Refined TSC clocksource calibration: 399.076 MHz
[ 12.557053] Switching to clocksource tsc
[ 12.620928] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 12.716539] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 12.951350] IOAPIC[0]: Set routing entry (1-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:1)
[ 12.953625] pch_udc 0000:00:14.2: setting latency timer to 64
[ 12.954024] pch_udc 0000:00:14.2: irq 40 for MSI/MSI-X
[ 12.954640] pch_udc 0000:00:14.2: enabling Mem-Wr-Inval
[ 13.023345] g_serial: Vendor 0x8086 Product 0xbabe
[ 13.028291] g_serial gadget: Gadget Serial v2.4
[ 13.033429] g_serial gadget: g_serial ready
[ 13.093772] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 13.100739] stmmaceth 0000:00:14.6: enabling bus mastering
[ 13.100825] stmmaceth 0000:00:14.6: setting latency timer to 64
[ 13.101217] stmmaceth 0000:00:14.6: irq 41 for MSI/MSI-X
[ 13.101434] stmmac MSI mode enabled
[ 13.104797] Vendor 0x8086 Device 0x0937
[ 13.109034] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 13.114263] DMA HW capability register supported
[ 13.118842] Enhanced/Alternate descriptors
[ 13.123381] RX Checksum Offload Engine supported (type 2)
[ 13.128918] TX Checksum insertion supported
[ 13.133344] Enable RX Mitigation via HW Watchdog Timer
[ 13.188567] libphy: stmmac: probed
[ 13.192175] eth0: PHY ID 20005c90 at 1 IRQ 0 (stmmac-1:01) active
[ 13.263478] ACPI: bus type usb registered
[ 13.271233] usbcore: registered new interface driver usbfs
[ 13.279189] usbcore: registered new interface driver hub
[ 13.287095] usbcore: registered new device driver usb
[ 13.302212] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 13.357399] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 13.364624] ohci_hcd 0000:00:14.4: enabling bus mastering
[ 13.364710] ohci_hcd 0000:00:14.4: setting latency timer to 64
[ 13.364775] ohci_hcd 0000:00:14.4: OHCI Host Controller
[ 13.371281] ohci_hcd 0000:00:14.4: new USB bus registered, assigned bus number 1
[ 13.379058] ohci_hcd 0000:00:14.4: irq 16, io mem 0x9000c000
[ 13.461015] hub 1-0:1.0: USB hub found
[ 13.465419] hub 1-0:1.0: 2 ports detected
[ 13.523821] ehci-pci: EHCI PCI platform driver
[ 13.528795] ehci-pci 0000:00:14.3: enabling bus mastering
[ 13.528881] ehci-pci 0000:00:14.3: setting latency timer to 64
[ 13.528945] ehci-pci 0000:00:14.3: EHCI Host Controller
[ 13.534934] ehci-pci 0000:00:14.3: new USB bus registered, assigned bus number 2
[ 13.543544] ehci-pci 0000:00:14.3: enabling Mem-Wr-Inval
[ 13.543716] ehci-pci 0000:00:14.3: INSNREG01 is 0x007f007f
[ 13.549270] ehci-pci 0000:00:14.3: INSNREG01 is 0x007f007f
[ 13.555205] ehci-pci 0000:00:14.3: irq 19, io mem 0x9000d000
[ 13.580228] ehci-pci 0000:00:14.3: USB 2.0 started, EHCI 1.00
[ 13.592768] hub 2-0:1.0: USB hub found
[ 13.596778] hub 2-0:1.0: 2 ports detected
[ 13.660925] Initializing USB Mass Storage driver...
[ 13.668113] usbcore: registered new interface driver usb-storage
[ 13.674302] USB Mass Storage support registered.
[ 13.811615] intel_cln_gpio_probe UIO addr 0x90006000 internal_addr 0x00000000 size 3765649408 memtype 4096
[ 13.833004] intel_cln_gip 0000:00:15.2: setting latency timer to 64
[ 13.833413] intel_cln_gip 0000:00:15.2: irq 42 for MSI/MSI-X
[ 13.884688] cy8c9540a 0-0020: dev_id=0x40
[ 14.043687] at24 0-0050: byte_len looks suspicious (no power of 2)!
[ 14.050691] at24 0-0050: 11264 byte at24 EEPROM, writable, 1 bytes/write
[ 14.104017] i2c /dev entries driver
[ 14.267461] spi_pxa2xx_pci: `0' invalid for parameter `gpio_cs'
[ 14.318776] ce4100_spi 0000:00:15.0: enabling device (0000 -> 0002)
[ 14.325898] ce4100_spi 0000:00:15.0: enabling bus mastering
[ 14.325982] ce4100_spi 0000:00:15.0: setting latency timer to 64
[ 14.326384] ce4100_spi 0000:00:15.0: irq 43 for MSI/MSI-X
[ 14.329237] ce4100_spi 0000:00:15.1: enabling device (0000 -> 0002)
[ 14.336550] ce4100_spi 0000:00:15.1: enabling bus mastering
[ 14.336636] ce4100_spi 0000:00:15.1: setting latency timer to 64
[ 14.337035] ce4100_spi 0000:00:15.1: irq 44 for MSI/MSI-X
[ 14.349848] pxa2xx-spi pxa2xx-spi.0: registered master spi0
[ 14.350845] spi_master spi0: will run message pump with realtime priority
[ 14.360743] spi spi0.0: 1000000 Hz actual, PIO
[ 14.361129] spi spi0.0: setup mode 2, 8 bits/w, 5000000 Hz max --> 0
[ 14.365470] pxa2xx-spi pxa2xx-spi.0: registered child spi0.0
[ 14.367916] pxa2xx-spi pxa2xx-spi.1: registered master spi1
[ 14.368781] spi_master spi1: will run message pump with realtime priority
[ 14.376041] spi spi1.0: 5000000 Hz actual, PIO
[ 14.376146] spi spi1.0: setup mode 0, 8 bits/w, 50000000 Hz max --> 0
[ 14.386472] pxa2xx-spi pxa2xx-spi.1: registered child spi1.0
[ 14.591287] cfg80211: Calling CRDA to update world regulatory domain
[ 14.619272] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 14.625206] Copyright(c) 2003-2012 Intel Corporation
[ 14.814135] Bluetooth: Core ver 2.16
[ 14.819673] NET: Registered protocol family 31
[ 14.824298] Bluetooth: HCI device and connection manager initialized
[ 14.831439] Bluetooth: HCI socket layer initialized
[ 14.836452] Bluetooth: L2CAP socket layer initialized
[ 14.841933] Bluetooth: SCO socket layer initialized
[ 14.856846] usbcore: registered new interface driver btusb
[ 14.914962] usbcore: registered new interface driver usbhid
[ 14.920718] usbhid: USB HID core driver
[ 17.867005] eth0: device MAC address **:**:**:**:**:** dmesg（microSDメモリーカードへ書き込んだLinuxからの起動）
Ethernetに接続がない状態で起動したログです：
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.7-yocto-standard (clntonsw@irsswdev001) (gcc version 4.7.2 (GCC) ) #1 Tue Oct 1 00:09:01 IST 2013
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x0000000000096fff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000097000-0x0000000000097fff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000098000-0x000000000009ffff] usable
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000000f0defff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000f0df000-0x000000000f11efff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x000000000f11f000-0x000000000f1defff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000f1df000-0x000000000fedefff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x000000000fedf000-0x000000000feeefff] reserved
[ 0.000000] BIOS-e820: [mem 0x000000000feef000-0x000000000feeffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff800000-0x00000000ffffffff] reserved
[ 0.000000] Early serial console at MMIO32 0x8010f000 (options '115200n8')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.31 by EKI
[ 0.000000] efi: SMBIOS=0xfeee000 ACPI=0xf11e000 ACPI 2.0=0xf11e014
[ 0.000000] efi: mem00: type=7, attr=0xf, range=[0x0000000000000000-0x0000000000095000) (0MB)
[ 0.000000] efi: mem01: type=2, attr=0xf, range=[0x0000000000095000-0x0000000000097000) (0MB)
[ 0.000000] efi: mem02: type=0, attr=0xf, range=[0x0000000000097000-0x0000000000098000) (0MB)
[ 0.000000] efi: mem03: type=7, attr=0xf, range=[0x0000000000098000-0x00000000000a0000) (0MB)
[ 0.000000] efi: mem04: type=2, attr=0xf, range=[0x0000000000100000-0x0000000000301000) (2MB)
[ 0.000000] efi: mem05: type=7, attr=0xf, range=[0x0000000000301000-0x0000000001ede000) (27MB)
[ 0.000000] efi: mem06: type=4, attr=0xf, range=[0x0000000001ede000-0x0000000002000000) (1MB)
[ 0.000000] efi: mem07: type=7, attr=0xf, range=[0x0000000002000000-0x000000000c0e0000) (160MB)
[ 0.000000] efi: mem08: type=4, attr=0xf, range=[0x000000000c0e0000-0x000000000c100000) (0MB)
[ 0.000000] efi: mem09: type=7, attr=0xf, range=[0x000000000c100000-0x000000000d9df000) (24MB)
[ 0.000000] efi: mem10: type=2, attr=0xf, range=[0x000000000d9df000-0x000000000df40000) (5MB)
[ 0.000000] efi: mem11: type=4, attr=0xf, range=[0x000000000df40000-0x000000000df84000) (0MB)
[ 0.000000] efi: mem12: type=2, attr=0xf, range=[0x000000000df84000-0x000000000df87000) (0MB)
[ 0.000000] efi: mem13: type=1, attr=0xf, range=[0x000000000df87000-0x000000000dfc8000) (0MB)
[ 0.000000] efi: mem14: type=4, attr=0xf, range=[0x000000000dfc8000-0x000000000e458000) (4MB)
[ 0.000000] efi: mem15: type=3, attr=0xf, range=[0x000000000e458000-0x000000000e45f000) (0MB)
[ 0.000000] efi: mem16: type=4, attr=0xf, range=[0x000000000e45f000-0x000000000e4b9000) (0MB)
[ 0.000000] efi: mem17: type=3, attr=0xf, range=[0x000000000e4b9000-0x000000000e4c6000) (0MB)
[ 0.000000] efi: mem18: type=4, attr=0xf, range=[0x000000000e4c6000-0x000000000e4c8000) (0MB)
[ 0.000000] efi: mem19: type=3, attr=0xf, range=[0x000000000e4c8000-0x000000000e4ca000) (0MB)
[ 0.000000] efi: mem20: type=4, attr=0xf, range=[0x000000000e4ca000-0x000000000e4cd000) (0MB)
[ 0.000000] efi: mem21: type=3, attr=0xf, range=[0x000000000e4cd000-0x000000000e4d2000) (0MB)
[ 0.000000] efi: mem22: type=4, attr=0xf, range=[0x000000000e4d2000-0x000000000e4d3000) (0MB)
[ 0.000000] efi: mem23: type=3, attr=0xf, range=[0x000000000e4d3000-0x000000000e4e7000) (0MB)
[ 0.000000] efi: mem24: type=4, attr=0xf, range=[0x000000000e4e7000-0x000000000e4e8000) (0MB)
[ 0.000000] efi: mem25: type=3, attr=0xf, range=[0x000000000e4e8000-0x000000000e4ee000) (0MB)
[ 0.000000] efi: mem26: type=4, attr=0xf, range=[0x000000000e4ee000-0x000000000e4ef000) (0MB)
[ 0.000000] efi: mem27: type=3, attr=0xf, range=[0x000000000e4ef000-0x000000000e520000) (0MB)
[ 0.000000] efi: mem28: type=4, attr=0xf, range=[0x000000000e520000-0x000000000e534000) (0MB)
[ 0.000000] efi: mem29: type=3, attr=0xf, range=[0x000000000e534000-0x000000000e539000) (0MB)
[ 0.000000] efi: mem30: type=4, attr=0xf, range=[0x000000000e539000-0x000000000e53a000) (0MB)
[ 0.000000] efi: mem31: type=3, attr=0xf, range=[0x000000000e53a000-0x000000000e54b000) (0MB)
[ 0.000000] efi: mem32: type=4, attr=0xf, range=[0x000000000e54b000-0x000000000e55b000) (0MB)
[ 0.000000] efi: mem33: type=3, attr=0xf, range=[0x000000000e55b000-0x000000000e567000) (0MB)
[ 0.000000] efi: mem34: type=4, attr=0xf, range=[0x000000000e567000-0x000000000e57c000) (0MB)
[ 0.000000] efi: mem35: type=3, attr=0xf, range=[0x000000000e57c000-0x000000000e57e000) (0MB)
[ 0.000000] efi: mem36: type=4, attr=0xf, range=[0x000000000e57e000-0x000000000e5ad000) (0MB)
[ 0.000000] efi: mem37: type=3, attr=0xf, range=[0x000000000e5ad000-0x000000000e5b6000) (0MB)
[ 0.000000] efi: mem38: type=4, attr=0xf, range=[0x000000000e5b6000-0x000000000e5c2000) (0MB)
[ 0.000000] efi: mem39: type=3, attr=0xf, range=[0x000000000e5c2000-0x000000000e5d0000) (0MB)
[ 0.000000] efi: mem40: type=4, attr=0xf, range=[0x000000000e5d0000-0x000000000e5d3000) (0MB)
[ 0.000000] efi: mem41: type=3, attr=0xf, range=[0x000000000e5d3000-0x000000000e5ec000) (0MB)
[ 0.000000] efi: mem42: type=4, attr=0xf, range=[0x000000000e5ec000-0x000000000e710000) (1MB)
[ 0.000000] efi: mem43: type=3, attr=0xf, range=[0x000000000e710000-0x000000000e726000) (0MB)
[ 0.000000] efi: mem44: type=4, attr=0xf, range=[0x000000000e726000-0x000000000e728000) (0MB)
[ 0.000000] efi: mem45: type=3, attr=0xf, range=[0x000000000e728000-0x000000000e72f000) (0MB)
[ 0.000000] efi: mem46: type=4, attr=0xf, range=[0x000000000e72f000-0x000000000e734000) (0MB)
[ 0.000000] efi: mem47: type=3, attr=0xf, range=[0x000000000e734000-0x000000000e735000) (0MB)
[ 0.000000] efi: mem48: type=4, attr=0xf, range=[0x000000000e735000-0x000000000e736000) (0MB)
[ 0.000000] efi: mem49: type=3, attr=0xf, range=[0x000000000e736000-0x000000000e752000) (0MB)
[ 0.000000] efi: mem50: type=4, attr=0xf, range=[0x000000000e752000-0x000000000e753000) (0MB)
[ 0.000000] efi: mem51: type=3, attr=0xf, range=[0x000000000e753000-0x000000000e759000) (0MB)
[ 0.000000] efi: mem52: type=4, attr=0xf, range=[0x000000000e759000-0x000000000e774000) (0MB)
[ 0.000000] efi: mem53: type=3, attr=0xf, range=[0x000000000e774000-0x000000000e776000) (0MB)
[ 0.000000] efi: mem54: type=4, attr=0xf, range=[0x000000000e776000-0x000000000e777000) (0MB)
[ 0.000000] efi: mem55: type=3, attr=0xf, range=[0x000000000e777000-0x000000000e77b000) (0MB)
[ 0.000000] efi: mem56: type=4, attr=0xf, range=[0x000000000e77b000-0x000000000e77c000) (0MB)
[ 0.000000] efi: mem57: type=3, attr=0xf, range=[0x000000000e77c000-0x000000000e785000) (0MB)
[ 0.000000] efi: mem58: type=4, attr=0xf, range=[0x000000000e785000-0x000000000e789000) (0MB)
[ 0.000000] efi: mem59: type=3, attr=0xf, range=[0x000000000e789000-0x000000000e78d000) (0MB)
[ 0.000000] efi: mem60: type=4, attr=0xf, range=[0x000000000e78d000-0x000000000e79f000) (0MB)
[ 0.000000] efi: mem61: type=3, attr=0xf, range=[0x000000000e79f000-0x000000000e7a1000) (0MB)
[ 0.000000] efi: mem62: type=4, attr=0xf, range=[0x000000000e7a1000-0x000000000e7a9000) (0MB)
[ 0.000000] efi: mem63: type=3, attr=0xf, range=[0x000000000e7a9000-0x000000000e7af000) (0MB)
[ 0.000000] efi: mem64: type=4, attr=0xf, range=[0x000000000e7af000-0x000000000e7b7000) (0MB)
[ 0.000000] efi: mem65: type=3, attr=0xf, range=[0x000000000e7b7000-0x000000000e7bb000) (0MB)
[ 0.000000] efi: mem66: type=4, attr=0xf, range=[0x000000000e7bb000-0x000000000e7cc000) (0MB)
[ 0.000000] efi: mem67: type=3, attr=0xf, range=[0x000000000e7cc000-0x000000000e7d1000) (0MB)
[ 0.000000] efi: mem68: type=4, attr=0xf, range=[0x000000000e7d1000-0x000000000f0df000) (9MB)
[ 0.000000] efi: mem69: type=9, attr=0xf, range=[0x000000000f0df000-0x000000000f11f000) (0MB)
[ 0.000000] efi: mem70: type=5, attr=0x800000000000000f, range=[0x000000000f11f000-0x000000000f17f000) (0MB)
[ 0.000000] efi: mem71: type=6, attr=0x800000000000000f, range=[0x000000000f17f000-0x000000000f1df000) (0MB)
[ 0.000000] efi: mem72: type=10, attr=0xf, range=[0x000000000f1df000-0x000000000fedf000) (13MB)
[ 0.000000] efi: mem73: type=0, attr=0xf, range=[0x000000000fedf000-0x000000000feef000) (0MB)
[ 0.000000] efi: mem74: type=4, attr=0xf, range=[0x000000000feef000-0x000000000fef0000) (0MB)
[ 0.000000] efi: mem75: type=11, attr=0x8000000000000000, range=[0x00000000e0000000-0x00000000f0000000) (256MB)
[ 0.000000] efi: mem76: type=11, attr=0x8000000000000000, range=[0x00000000fed1c000-0x00000000fed20000) (0MB)
[ 0.000000] efi: mem77: type=11, attr=0x8000000000000001, range=[0x00000000ff800000-0x0000000100000000) (8MB)
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0xfef0 max_arch_pfn = 0x1000000
[ 0.000000] Scan for SMP in [mem 0x00000000-0x000003ff]
[ 0.000000] Scan for SMP in [mem 0x0009fc00-0x0009ffff]
[ 0.000000] Scan for SMP in [mem 0x000f0000-0x000fffff]
[ 0.000000] Scan for SMP in [mem 0x000aaaa0-0x000aae9f]
[ 0.000000] initial memory mapped: [mem 0x00000000-0x01ffffff]
[ 0.000000] Base memory trampoline at [c009b000] 9b000 size 16384
[ 0.000000] init_memory_mapping: [mem 0x00000000-0x0feeffff]
[ 0.000000] [mem 0x00000000-0x001fffff] page 4k
[ 0.000000] [mem 0x00200000-0x0fdfffff] page 2M
[ 0.000000] [mem 0x0fe00000-0x0feeffff] page 4k
[ 0.000000] kernel direct mapping tables up to 0xfeeffff @ [mem 0x01ed8000-0x01eddfff]
[ 0.000000] RAMDISK: [mem 0x0d9df000-0x0db3efff]
[ 0.000000] ACPI: RSDP 0f11e014 00024 (v02 INTEL )
[ 0.000000] ACPI: XSDT 0f11d0e8 0006C (v01 INTEL TIANO 00000003 01000013)
[ 0.000000] ACPI: FACP 0f11b000 000F4 (v03 INTEL TIANO 00000003 INTL 0100000D)
[ 0.000000] ACPI: DSDT 0f113000 015A2 (v01 INTEL ClantonN 00000003 INTL 20081031)
[ 0.000000] ACPI: FACS 0f2c7000 00040
[ 0.000000] ACPI: UEFI 0fcd5000 00042 (v01 00000000 00000000)
[ 0.000000] ACPI: APIC 0f11c000 0005A (v01 INTEL TIANO 00000001 MSFT 00000000)
[ 0.000000] ACPI: HPET 0f11a000 00038 (v01 00000001 00000000)
[ 0.000000] ACPI: MCFG 0f119000 0003C (v01 00000001 00000000)
[ 0.000000] ACPI: SSDT 0f118000 004D8 (v01 SsgPmm Cpu0Cst 00000011 INTL 20081031)
[ 0.000000] ACPI: SSDT 0f117000 0043F (v01 SsgPmm Cpu0Ist 00000012 INTL 20081031)
[ 0.000000] ACPI: SSDT 0f116000 0013B (v01 SsgPmm Cpu0Tst 00000013 INTL 20081031)
[ 0.000000] ACPI: SSDT 0f115000 00056 (v01 SsgPmm CpuPm 00000010 INTL 20081031)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffffb000 ( fee00000)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 254MB LOWMEM available.
[ 0.000000] mapped low ram: 0 - 0fef0000
[ 0.000000] low ram: 0 - 0fef0000
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00010000-0x0feeffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x00096fff]
[ 0.000000] node 0: [mem 0x00098000-0x0009ffff]
[ 0.000000] node 0: [mem 0x00100000-0x0f0defff]
[ 0.000000] node 0: [mem 0x0feef000-0x0feeffff]
[ 0.000000] On node 0 totalpages: 61551
[ 0.000000] free_area_init_node: node 0, pgdat c1484720, node_mem_map cdd40200
[ 0.000000] Normal zone: 510 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 61041 pages, LIFO batch:15
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] mapped APIC to ffffb000 ( fee00000)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: Assigned apic_id 1
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 00, APIC ID 1, APIC INT 02
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] Int: type 0, pol 1, trig 3, bus 00, IRQ 09, APIC ID 1, APIC INT 09
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 01, APIC ID 1, APIC INT 01
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 03, APIC ID 1, APIC INT 03
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 04, APIC ID 1, APIC INT 04
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 05, APIC ID 1, APIC INT 05
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 06, APIC ID 1, APIC INT 06
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 07, APIC ID 1, APIC INT 07
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 08, APIC ID 1, APIC INT 08
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0a, APIC ID 1, APIC INT 0a
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0b, APIC ID 1, APIC INT 0b
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0c, APIC ID 1, APIC INT 0c
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0d, APIC ID 1, APIC INT 0d
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0e, APIC ID 1, APIC INT 0e
[ 0.000000] Int: type 0, pol 0, trig 0, bus 00, IRQ 0f, APIC ID 1, APIC INT 0f
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] e820: [mem 0x0fef0000-0xdfffffff] available for PCI devices
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61041
[ 0.000000] Kernel command line: root=/dev/ram0 console=ttyS1,115200n8 earlycon=uart8250,mmio32,0x8010f000,115200n8 reboot=efi,warm apic=debug rw LABEL=boot debugshell=5 efi_main=0x000000014ca7b2ad jmp_code32=0x0000000185f3a78d
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] Initializing CPU#0
[ 0.000000] Initializing HighMem for node 0 (00000000:00000000)
[ 0.000000] Memory: 213068k/261056k available (3098k kernel code, 33136k reserved, 1547k data, 272k init, 0k highmem)
[ 0.000000] virtual kernel memory layout:
[ 0.000000] fixmap : 0xfffa2000 - 0xfffff000 ( 372 kB)
[ 0.000000] pkmap : 0xffc00000 - 0xffe00000 (2048 kB)
[ 0.000000] vmalloc : 0xd06f0000 - 0xffbfe000 ( 757 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xcfef0000 ( 254 MB)
[ 0.000000] .init : 0xc148a000 - 0xc14ce000 ( 272 kB)
[ 0.000000] .data : 0xc1306812 - 0xc1489480 (1547 kB)
[ 0.000000] .text : 0xc1000000 - 0xc1306812 (3098 kB)
[ 0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.000000] SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:2304 nr_irqs:256 16
[ 0.000000] CPU 0 irqstacks, hard=c0090000 soft=c0092000
[ 0.000000] spurious 8259A interrupt: IRQ7.
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000000] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000000] ... MAX_LOCK_DEPTH: 48
[ 0.000000] ... MAX_LOCKDEP_KEYS: 8191
[ 0.000000] ... CLASSHASH_SIZE: 4096
[ 0.000000] ... MAX_LOCKDEP_ENTRIES: 16384
[ 0.000000] ... MAX_LOCKDEP_CHAINS: 32768
[ 0.000000] ... CHAINHASH_SIZE: 16384
[ 0.000000] memory used by lock dependency info: 3567 kB
[ 0.000000] per task-struct memory footprint: 1152 bytes
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] tsc: Detected 399.088 MHz processor
[ 0.010015] Calibrating delay loop (skipped), value calculated using timer frequency.. 798.17 BogoMIPS (lpj=3990880)
[ 0.010136] pid_max: default: 32768 minimum: 301
[ 0.408063] Security Framework initialized
[ 0.408336] Mount-cache hash table entries: 512
[ 0.417566] Initializing cgroup subsys cpuacct
[ 0.417736] Initializing cgroup subsys freezer
[ 0.418536] Intel Pentium with F0 0F bug - workaround enabled.
[ 0.418795] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.418795] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0
[ 0.418795] tlb_flushall_shift: 6
[ 0.418938] CPU: Intel 05/09 (fam: 05, model: 09, stepping: 00)
[ 0.419173] ACPI: Core revision 20121018
[ 0.510385] Performance Events: no PMU driver, software events only.
[ 0.515309] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.515389] Getting VERSION: 30010
[ 0.515444] Getting VERSION: 30010
[ 0.515497] Getting ID: 0
[ 0.515544] Getting ID: f000000
[ 0.515596] Getting LVT0: 700
[ 0.515647] Getting LVT1: 400
[ 0.515715] enabled ExtINT on CPU#0
[ 0.516129] ENABLING IO-APIC IRQs
[ 0.516184] Synchronizing Arb IDs.
[ 0.516234] init IO_APIC IRQs
[ 0.516266] apic 1 pin 0 not connected
[ 0.516570] IOAPIC[0]: Set routing entry (1-1 -> 0x31 -> IRQ 1 Mode:0 Active:0 Dest:1)
[ 0.516691] IOAPIC[0]: Set routing entry (1-2 -> 0x30 -> IRQ 0 Mode:0 Active:0 Dest:1)
[ 0.516801] IOAPIC[0]: Set routing entry (1-3 -> 0x33 -> IRQ 3 Mode:0 Active:0 Dest:1)
[ 0.516911] IOAPIC[0]: Set routing entry (1-4 -> 0x34 -> IRQ 4 Mode:0 Active:0 Dest:1)
[ 0.517021] IOAPIC[0]: Set routing entry (1-5 -> 0x35 -> IRQ 5 Mode:0 Active:0 Dest:1)
[ 0.517131] IOAPIC[0]: Set routing entry (1-6 -> 0x36 -> IRQ 6 Mode:0 Active:0 Dest:1)
[ 0.517241] IOAPIC[0]: Set routing entry (1-7 -> 0x37 -> IRQ 7 Mode:0 Active:0 Dest:1)
[ 0.517350] IOAPIC[0]: Set routing entry (1-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[ 0.517459] IOAPIC[0]: Set routing entry (1-9 -> 0x39 -> IRQ 9 Mode:1 Active:0 Dest:1)
[ 0.517568] IOAPIC[0]: Set routing entry (1-10 -> 0x3a -> IRQ 10 Mode:0 Active:0 Dest:1)
[ 0.517677] IOAPIC[0]: Set routing entry (1-11 -> 0x3b -> IRQ 11 Mode:0 Active:0 Dest:1)
[ 0.517787] IOAPIC[0]: Set routing entry (1-12 -> 0x3c -> IRQ 12 Mode:0 Active:0 Dest:1)
[ 0.517897] IOAPIC[0]: Set routing entry (1-13 -> 0x3d -> IRQ 13 Mode:0 Active:0 Dest:1)
[ 0.518007] IOAPIC[0]: Set routing entry (1-14 -> 0x3e -> IRQ 14 Mode:0 Active:0 Dest:1)
[ 0.518118] IOAPIC[0]: Set routing entry (1-15 -> 0x3f -> IRQ 15 Mode:0 Active:0 Dest:1)
[ 0.518195] apic 1 pin 16 not connected
[ 0.518231] apic 1 pin 17 not connected
[ 0.518261] apic 1 pin 18 not connected
[ 0.518288] apic 1 pin 19 not connected
[ 0.518315] apic 1 pin 20 not connected
[ 0.518342] apic 1 pin 21 not connected
[ 0.518368] apic 1 pin 22 not connected
[ 0.518395] apic 1 pin 23 not connected
[ 0.518586] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.618810] Using local APIC timer interrupts.
[ 0.618810] calibrating APIC timer ...
[ 0.620000] ... lapic delta = 2494191
[ 0.620000] ... PM-Timer delta = 357949
[ 0.620000] ... PM-Timer result ok
[ 0.620000] ..... delta 2494191
[ 0.620000] ..... mult: 107124687
[ 0.620000] ..... calibration result: 3990705
[ 0.620000] ..... CPU clock speed is 399.0706 MHz.
[ 0.620000] ..... host bus clock speed is 399.0705 MHz.
[ 0.620000] devtmpfs: initialized
[ 0.623256] PM: Registering ACPI NVS region [mem 0x0f1df000-0x0fedefff] (13631488 bytes)
[ 0.629303] RTC time: 19:47:20, date: 12/27/13
[ 0.632063] NET: Registered protocol family 16
[ 0.658034] ACPI: bus type pci registered
[ 0.660577] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.660698] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.660777] PCI: Using MMCONFIG for extended config space
[ 0.660848] PCI: Using configuration type 1 for base access
[ 0.810140] bio: create slab at 0
[ 0.814746] ACPI: Added _OSI(Module Device)
[ 0.814841] ACPI: Added _OSI(Processor Device)
[ 0.814924] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.815010] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.834784] ACPI: EC: Look up EC in DSDT
[ 0.898078] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.906265] ACPI: Interpreter enabled
[ 0.906331] ACPI: (supports S0 S3 S5)
[ 0.907157] ACPI: Using IOAPIC for interrupt routing
[ 1.071292] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 1.076919] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 1.077083] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 1.097226] PCI host bridge to bus 0000:00
[ 1.097345] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 1.097443] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 1.097540] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 1.097636] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 1.097738] pci_bus 0000:00: root bus resource [mem 0x10000000-0xfebfffff]
[ 1.098001] pci_bus 0000:00: scanning bus
[ 1.098715] pci 0000:00:00.0: [8086:0958] type 00 class 0x060000
[ 1.098843] pci 0000:00:00.0: calling quirk_mmio_always_on+0x0/0x10
[ 1.100799] pci 0000:00:14.0: [8086:08a7] type 00 class 0x080501
[ 1.100994] pci 0000:00:14.0: reg 10: [mem 0x90010000-0x90010fff]
[ 1.101648] pci 0000:00:14.0: PME# supported from D0 D3hot
[ 1.102202] pci 0000:00:14.0: PME# disabled
[ 1.102475] pci 0000:00:14.1: [8086:0936] type 00 class 0x070002
[ 1.102662] pci 0000:00:14.1: reg 10: [mem 0x9000f000-0x9000ffff]
[ 1.102783] pci 0000:00:14.1: reg 14: [mem 0x9000e000-0x9000efff]
[ 1.103384] pci 0000:00:14.1: PME# supported from D0 D3hot
[ 1.103475] pci 0000:00:14.1: PME# disabled
[ 1.103733] pci 0000:00:14.2: [8086:0939] type 00 class 0x0c03fe
[ 1.103919] pci 0000:00:14.2: reg 10: [mem 0x90004000-0x90005fff]
[ 1.104571] pci 0000:00:14.2: PME# supported from D0 D3hot
[ 1.104660] pci 0000:00:14.2: PME# disabled
[ 1.104933] pci 0000:00:14.3: [8086:0939] type 00 class 0x0c0320
[ 1.105134] pci 0000:00:14.3: reg 10: [mem 0x9000d000-0x9000dfff]
[ 1.105827] pci 0000:00:14.3: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.105917] pci 0000:00:14.3: PME# disabled
[ 1.106189] pci 0000:00:14.4: [8086:093a] type 00 class 0x0c0310
[ 1.106375] pci 0000:00:14.4: reg 10: [mem 0x9000c000-0x9000cfff]
[ 1.107026] pci 0000:00:14.4: PME# supported from D0 D3hot
[ 1.107115] pci 0000:00:14.4: PME# disabled
[ 1.107377] pci 0000:00:14.5: [8086:0936] type 00 class 0x070002
[ 1.107563] pci 0000:00:14.5: reg 10: [mem 0x9000b000-0x9000bfff]
[ 1.107685] pci 0000:00:14.5: reg 14: [mem 0x9000a000-0x9000afff]
[ 1.108287] pci 0000:00:14.5: PME# supported from D0 D3hot
[ 1.108378] pci 0000:00:14.5: PME# disabled
[ 1.108638] pci 0000:00:14.6: [8086:0937] type 00 class 0x020000
[ 1.108824] pci 0000:00:14.6: reg 10: [mem 0x90002000-0x90003fff]
[ 1.109476] pci 0000:00:14.6: PME# supported from D0 D3hot
[ 1.109565] pci 0000:00:14.6: PME# disabled
[ 1.109863] pci 0000:00:14.7: [8086:0937] type 00 class 0x020000
[ 1.110160] pci 0000:00:14.7: reg 10: [mem 0x90000000-0x90001fff]
[ 1.110817] pci 0000:00:14.7: PME# supported from D0 D3hot
[ 1.110907] pci 0000:00:14.7: PME# disabled
[ 1.111169] pci 0000:00:15.0: [8086:0935] type 00 class 0x0c8000
[ 1.111356] pci 0000:00:15.0: reg 10: [mem 0x90009000-0x90009fff]
[ 1.112008] pci 0000:00:15.0: PME# supported from D0 D3hot
[ 1.112097] pci 0000:00:15.0: PME# disabled
[ 1.112359] pci 0000:00:15.1: [8086:0935] type 00 class 0x0c8000
[ 1.112546] pci 0000:00:15.1: reg 10: [mem 0x90008000-0x90008fff]
[ 1.113198] pci 0000:00:15.1: PME# supported from D0 D3hot
[ 1.113289] pci 0000:00:15.1: PME# disabled
[ 1.113548] pci 0000:00:15.2: [8086:0934] type 00 class 0x0c8000
[ 1.113734] pci 0000:00:15.2: reg 10: [mem 0x90007000-0x90007fff]
[ 1.113854] pci 0000:00:15.2: reg 14: [mem 0x90006000-0x90006fff]
[ 1.114455] pci 0000:00:15.2: PME# supported from D0 D3hot
[ 1.114544] pci 0000:00:15.2: PME# disabled
[ 1.114866] pci 0000:00:17.0: [8086:11c3] type 01 class 0x060400
[ 1.115265] pci 0000:00:17.0: calling pci_fixup_transparent_bridge+0x0/0x30
[ 1.115649] pci 0000:00:17.0: PME# supported from D0 D3hot D3cold
[ 1.115736] pci 0000:00:17.0: PME# disabled
[ 1.116019] pci 0000:00:17.1: [8086:11c4] type 01 class 0x060400
[ 1.116416] pci 0000:00:17.1: calling pci_fixup_transparent_bridge+0x0/0x30
[ 1.116801] pci 0000:00:17.1: PME# supported from D0 D3hot D3cold
[ 1.116888] pci 0000:00:17.1: PME# disabled
[ 1.117287] pci 0000:00:1f.0: [8086:095e] type 00 class 0x060100
[ 1.117852] pci_bus 0000:00: fixups for bus
[ 1.117934] pci 0000:00:17.0: scanning [bus 01-01] behind bridge, pass 0
[ 1.118317] pci_bus 0000:01: scanning bus
[ 1.118392] pci_bus 0000:01: fixups for bus
[ 1.118446] pci 0000:00:17.0: PCI bridge to [bus 01]
[ 1.118598] pci_bus 0000:01: bus scan returning with max=01
[ 1.118680] pci 0000:00:17.1: scanning [bus 02-02] behind bridge, pass 0
[ 1.119097] pci_bus 0000:02: scanning bus
[ 1.119173] pci_bus 0000:02: fixups for bus
[ 1.119226] pci 0000:00:17.1: PCI bridge to [bus 02]
[ 1.119377] pci_bus 0000:02: bus scan returning with max=02
[ 1.119463] pci 0000:00:17.0: scanning [bus 01-01] behind bridge, pass 1
[ 1.119552] pci 0000:00:17.1: scanning [bus 02-02] behind bridge, pass 1
[ 1.119630] pci_bus 0000:00: bus scan returning with max=02
[ 1.119680] pci_bus 0000:00: on NUMA node 0
[ 1.120387] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
[ 1.122933] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX1._PRT]
[ 1.129079] pci0000:00: ACPI _OSC support notification failed, disabling PCIe ASPM
[ 1.129185] pci0000:00: Unable to request _OSC control (_OSC support mask: 0x08)
[ 1.196067] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.200791] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.204752] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.208698] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.212751] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.216704] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.220817] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.224767] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 11 12) *0, disabled.
[ 1.236247] vgaarb: loaded
[ 1.241774] SCSI subsystem initialized
[ 1.253951] PCI: Using ACPI for IRQ routing
[ 1.282852] PCI: pci_cache_line_size set to 32 bytes
[ 1.283006] pci 0000:00:14.0: BAR 0: reserving [mem 0x90010000-0x90010fff flags 0x40200] (d=0, p=0)
[ 1.283118] pci 0000:00:14.1: BAR 0: reserving [mem 0x9000f000-0x9000ffff flags 0x40200] (d=0, p=0)
[ 1.283195] pci 0000:00:14.1: BAR 1: reserving [mem 0x9000e000-0x9000efff flags 0x40200] (d=0, p=0)
[ 1.283296] pci 0000:00:14.2: BAR 0: reserving [mem 0x90004000-0x90005fff flags 0x40200] (d=0, p=0)
[ 1.283401] pci 0000:00:14.3: BAR 0: reserving [mem 0x9000d000-0x9000dfff flags 0x40200] (d=0, p=0)
[ 1.283506] pci 0000:00:14.4: BAR 0: reserving [mem 0x9000c000-0x9000cfff flags 0x40200] (d=0, p=0)
[ 1.283611] pci 0000:00:14.5: BAR 0: reserving [mem 0x9000b000-0x9000bfff flags 0x40200] (d=0, p=0)
[ 1.283688] pci 0000:00:14.5: BAR 1: reserving [mem 0x9000a000-0x9000afff flags 0x40200] (d=0, p=0)
[ 1.283850] pci 0000:00:15.2: BAR 0: reserving [mem 0x90007000-0x90007fff flags 0x40200] (d=0, p=0)
[ 1.283928] pci 0000:00:15.2: BAR 1: reserving [mem 0x90006000-0x90006fff flags 0x40200] (d=0, p=0)
[ 1.284179] pci 0000:00:14.6: BAR 0: reserving [mem 0x90002000-0x90003fff flags 0x40200] (d=1, p=1)
[ 1.284285] pci 0000:00:14.7: BAR 0: reserving [mem 0x90000000-0x90001fff flags 0x40200] (d=1, p=1)
[ 1.284389] pci 0000:00:15.0: BAR 0: reserving [mem 0x90009000-0x90009fff flags 0x40200] (d=1, p=1)
[ 1.284495] pci 0000:00:15.1: BAR 0: reserving [mem 0x90008000-0x90008fff flags 0x40200] (d=1, p=1)
[ 1.284657] e820: reserve RAM buffer [mem 0x00097000-0x0009ffff]
[ 1.284717] e820: reserve RAM buffer [mem 0x0f0df000-0x0fffffff]
[ 1.284773] e820: reserve RAM buffer [mem 0x0fef0000-0x0fffffff]
[ 1.294671] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 1.294786] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 1.294897] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[ 1.298844] Switching to clocksource hpet
[ 1.298844] pnp: PnP ACPI init
[ 1.298844] ACPI: bus type pnp registered
[ 1.302005] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 1.302140] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 1.302262] system 00:00: [mem 0x000c0000-0x000dffff] has been reserved
[ 1.302392] system 00:00: [mem 0x000e0000-0x000fffff] could not be reserved
[ 1.302519] system 00:00: [mem 0xff800000-0xffffffff] has been reserved
[ 1.303077] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.315456] pnp 00:01: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 1.318187] pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
[ 1.332219] system 00:03: [io 0x1000-0x100f] has been reserved
[ 1.332347] system 00:03: [io 0x1010-0x101f] has been reserved
[ 1.332467] system 00:03: [io 0x1100-0x113f] has been reserved
[ 1.332588] system 00:03: [io 0x1080-0x10bf] has been reserved
[ 1.332709] system 00:03: [io 0x1040-0x107f] has been reserved
[ 1.332831] system 00:03: [io 0x1020-0x103f] has been reserved
[ 1.332954] system 00:03: [io 0x1140-0x117f] has been reserved
[ 1.333119] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 1.336647] IOAPIC[0]: Set routing entry (1-8 -> 0x38 -> IRQ 8 Mode:0 Active:0 Dest:1)
[ 1.339064] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 1.343250] pnp 00:05: Plug and Play ACPI device, IDs PNP0003 (active)
[ 1.343509] pnp: PnP ACPI: found 6 devices
[ 1.343587] ACPI: ACPI bus type pnp unregistered
[ 1.560742] pci 0000:00:17.0: bridge window [io 0x1000-0x0fff] to [bus 01] add_size 1000
[ 1.560830] pci 0000:00:17.0: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 01] add_size 200000
[ 1.560903] pci 0000:00:17.0: bridge window [mem 0x00100000-0x000fffff] to [bus 01] add_size 200000
[ 1.561033] pci 0000:00:17.1: bridge window [io 0x1000-0x0fff] to [bus 02] add_size 1000
[ 1.561110] pci 0000:00:17.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02] add_size 200000
[ 1.561181] pci 0000:00:17.1: bridge window [mem 0x00100000-0x000fffff] to [bus 02] add_size 200000
[ 1.561313] pci 0000:00:17.0: res[8]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 1.561376] pci 0000:00:17.0: res[9]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 1.561433] pci 0000:00:17.1: res[8]=[mem 0x00100000-0x000fffff] get_res_add_size add_size 200000
[ 1.561492] pci 0000:00:17.1: res[9]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 1.561549] pci 0000:00:17.0: res[7]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 1.561605] pci 0000:00:17.1: res[7]=[io 0x1000-0x0fff] get_res_add_size add_size 1000
[ 1.561699] pci 0000:00:17.0: BAR 8: assigned [mem 0x10000000-0x101fffff]
[ 1.561838] pci 0000:00:17.0: BAR 9: assigned [mem 0x10200000-0x103fffff 64bit pref]
[ 1.561979] pci 0000:00:17.1: BAR 8: assigned [mem 0x10400000-0x105fffff]
[ 1.562116] pci 0000:00:17.1: BAR 9: assigned [mem 0x10600000-0x107fffff 64bit pref]
[ 1.562263] pci 0000:00:17.0: BAR 7: assigned [io 0x2000-0x2fff]
[ 1.562399] pci 0000:00:17.1: BAR 7: assigned [io 0x3000-0x3fff]
[ 1.562532] pci 0000:00:17.0: PCI bridge to [bus 01]
[ 1.562643] pci 0000:00:17.0: bridge window [io 0x2000-0x2fff]
[ 1.562772] pci 0000:00:17.0: bridge window [mem 0x10000000-0x101fffff]
[ 1.562901] pci 0000:00:17.0: bridge window [mem 0x10200000-0x103fffff 64bit pref]
[ 1.563044] pci 0000:00:17.1: PCI bridge to [bus 02]
[ 1.563150] pci 0000:00:17.1: bridge window [io 0x3000-0x3fff]
[ 1.563278] pci 0000:00:17.1: bridge window [mem 0x10400000-0x105fffff]
[ 1.563405] pci 0000:00:17.1: bridge window [mem 0x10600000-0x107fffff 64bit pref]
[ 1.563681] IOAPIC[0]: Set routing entry (1-20 -> 0x41 -> IRQ 20 Mode:1 Active:1 Dest:1)
[ 1.563910] IOAPIC[0]: Set routing entry (1-21 -> 0x51 -> IRQ 21 Mode:1 Active:1 Dest:1)
[ 1.564037] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 1.564094] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 1.564146] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 1.564199] pci_bus 0000:00: resource 7 [mem 0x10000000-0xfebfffff]
[ 1.564256] pci_bus 0000:01: resource 0 [io 0x2000-0x2fff]
[ 1.564309] pci_bus 0000:01: resource 1 [mem 0x10000000-0x101fffff]
[ 1.564365] pci_bus 0000:01: resource 2 [mem 0x10200000-0x103fffff 64bit pref]
[ 1.564418] pci_bus 0000:02: resource 0 [io 0x3000-0x3fff]
[ 1.564471] pci_bus 0000:02: resource 1 [mem 0x10400000-0x105fffff]
[ 1.564526] pci_bus 0000:02: resource 2 [mem 0x10600000-0x107fffff 64bit pref]
[ 1.565496] NET: Registered protocol family 2
[ 1.570266] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 1.570866] TCP bind hash table entries: 2048 (order: 4, 73728 bytes)
[ 1.573147] TCP: Hash tables configured (established 2048 bind 2048)
[ 1.573797] TCP: reno registered
[ 1.573919] UDP hash table entries: 256 (order: 2, 20480 bytes)
[ 1.574602] UDP-Lite hash table entries: 256 (order: 2, 20480 bytes)
[ 1.576933] NET: Registered protocol family 1
[ 1.577328] pci 0000:00:14.2: calling quirk_usb_early_handoff+0x0/0x670
[ 1.577459] pci 0000:00:14.3: calling quirk_usb_early_handoff+0x0/0x670
[ 1.577653] IOAPIC[0]: Set routing entry (1-19 -> 0x61 -> IRQ 19 Mode:1 Active:1 Dest:1)
[ 1.578089] pci 0000:00:14.4: calling quirk_usb_early_handoff+0x0/0x670
[ 1.578308] IOAPIC[0]: Set routing entry (1-16 -> 0x71 -> IRQ 16 Mode:1 Active:1 Dest:1)
[ 1.578645] pci 0000:00:14.6: calling quirk_e100_interrupt+0x0/0x1b0
[ 1.578784] pci 0000:00:14.7: calling quirk_e100_interrupt+0x0/0x1b0
[ 1.579039] PCI: CLS 0 bytes, default 32
[ 1.581660] Trying to unpack rootfs image as initramfs...
[ 2.230400] Freeing initrd memory: 1408k freed
[ 2.248778] microcode: Intel CPU family 0x5 not supported
[ 2.255249] resource map sanity check conflict: 0xfff00000 0x1002fffff 0xff800000 0xffffffff reserved
[ 2.255361] ------------[ cut here ]------------
[ 2.255477] WARNING: at /build/clntonsw/slave_magnum/meta-clanton/build/compile/yocto_build/tmp/work/clanton-poky-linux-uclibc/linux-yocto-clanton/3.8-r0/linux/arch/x86/mm/ioremap.c:171 __ioremap_caller+0x27a/0x440()
[ 2.255639] Info: mapping multiple BARs. Your kernel is fine.
[ 2.255701] Modules linked in:
[ 2.255789] Pid: 1, comm: swapper Not tainted 3.8.7-yocto-standard #1
[ 2.255859] Call Trace:
[ 2.255957] [] warn_slowpath_common+0x5f/0x80
[ 2.256072] [] ? __ioremap_caller+0x27a/0x440
[ 2.256182] [] ? __ioremap_caller+0x27a/0x440
[ 2.256297] [] warn_slowpath_fmt+0x2e/0x30
[ 2.256407] [] __ioremap_caller+0x27a/0x440
[ 2.256523] [] ? intel_cln_board_data_init+0x1a/0x19d
[ 2.256632] [] ? efi_capsule_update_init+0x8d/0x8d
[ 2.256743] [] ioremap_nocache+0x1a/0x20
[ 2.256851] [] ? intel_cln_board_data_init+0x1a/0x19d
[ 2.256961] [] intel_cln_board_data_init+0x1a/0x19d
[ 2.257061] [] ? sysfs_add_file+0x13/0x20
[ 2.257151] [] ? sysfs_create_file+0x1c/0x20
[ 2.257251] [] ? efi_capsule_update_init+0x8d/0x8d
[ 2.257350] [] do_one_initcall+0x10a/0x150
[ 2.257445] [] kernel_init_freeable+0x106/0x1a0
[ 2.257539] [] ? do_early_param+0x7a/0x7a
[ 2.257646] [] kernel_init+0xb/0xd0
[ 2.257745] [] ret_from_kernel_thread+0x1b/0x30
[ 2.257851] [] ? rest_init+0xb0/0xb0
[ 2.258003] ---[ end trace 56c4136d52eafbcb ]---
[ 2.258099] MFH: mfh @ 0xe1008000: id 0x5f4d4648 ver 0x00000001 entries 0x0000000a
[ 2.260869] MFH: Warning platform data MFH missing - using hardcoded offsets
[ 2.266248] resource map sanity check conflict: 0xfff10000 0x100000075 0xff800000 0xffffffff reserved
[ 2.266513] CLN-PLT: Clanton Platform ID = 6
[ 2.289903] Intel Clanton side-band driver registered
[ 2.294875] IMR setup complete
[ 2.297192] eSRAM CTRL 0x047f3f91 block 0x00000000
[ 2.297265] eSRAM pages 128
[ 2.318717] intel_cln_esram_test_probe/Oct 1 2013/00:07:49 complete OK !!
[ 2.337799] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 2.481638] msgmni has been set to 456
[ 2.494560] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 2.494947] io scheduler noop registered
[ 2.495031] io scheduler deadline registered
[ 2.495248] io scheduler cfq registered (default)
[ 2.535273] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 2.536159] ACPI: Sleep Button [SLPB]
[ 2.538842] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 2.539023] ACPI: Power Button [PWRB]
[ 2.707190] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 2.720682] IOAPIC[0]: Set routing entry (1-17 -> 0x81 -> IRQ 17 Mode:1 Active:1 Dest:1)
[ 2.721147] Setup PCI port: port 0, irq 17, type 2
[ 2.768924] 0000:00:14.1: ttyS0 at MMIO 0x9000f000 (irq = 17) is a 16550A
[ 2.773422] Setup PCI port: port 0, irq 17, type 2
[ 2.797243] 0000:00:14.5: ttyS1 at MMIO 0x9000b000 (irq = 17) is a 16550A
[ 2.798470] console [ttyS1] enabled, bootconsole disabled
[ 2.811521] Real Time Clock Driver v1.12b
[ 2.828783] brd: module loaded
[ 2.847748] loop: module loaded
[ 2.853328] lpc_sch_probe BIOS_CNTL 0x00000101
[ 2.857848] lpc_sch_probe new BIOS_CNTL 0x00000101
[ 2.862835] lpc_sch_probe RCBA @ 0xfed1c000
[ 2.890990] cpuidle: using governor ladder
[ 2.895159] cpuidle: using governor menu
[ 2.901047] sdhci: Secure Digital Host Controller Interface driver
[ 2.907280] sdhci: Copyright(c) Pierre Ossman
[ 2.912022] sdhci-pci 0000:00:14.0: SDHCI controller found [8086:08a7] (rev 10)
[ 2.921879] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 2.923204] sdhci-pci 0000:00:14.0: setting latency timer to 64
[ 2.970253] mmc0: SDHCI controller on PCI [0000:00:14.0] using ADMA
[ 2.983784] sdhci-pltfm: SDHCI platform and OF driver helper
[ 3.006163] THRM: critical reset 104 c hot 95 c hardware failover 105 c
[ 3.034797] TCP: cubic registered
[ 3.038184] NET: Registered protocol family 17
[ 3.044485]
[ 3.044485] printing PIC contents
[ 3.044542] ... PIC IMR: ffff
[ 3.044572] ... PIC IRR: 0000
[ 3.044600] ... PIC ISR: 0000
[ 3.044628] ... PIC ELCR: 0000
[ 3.044661] printing local APIC contents on CPU#0/0:
[ 3.044692] ... APIC ID: 00000000 (0)
[ 3.048829] ... APIC VERSION: 00030010
[ 3.052616] ... APIC TASKPRI: 00000000 (00)
[ 3.052647] ... APIC ARBPRI: 00000000 (00)
[ 3.052675] ... APIC PROCPRI: 00000000
[ 3.052703] ... APIC RRR: 00000000
[ 3.052722] ... APIC LDR: 01000000
[ 3.052722] ... APIC DFR: ffffffff
[ 3.052722] ... APIC SPIV: 000001ff
[ 3.052722] ... APIC ISR field:
[ 3.052722] 0000000000000000000000000000000000000000000000000000000000000000
[ 3.052722] ... APIC TMR field:
[ 3.052722] 0000000000000000000000000002000000000000000000000000000000000000
[ 3.052722] ... APIC IRR field:
[ 3.052722] 0000000000000000000000000000000000000000000000000000000000008000
[ 3.052722] ... APIC ESR: 00000000
[ 3.052722] ... APIC ICR: 00088500
[ 3.052722] ... APIC ICR2: 00000000
[ 3.052722] ... APIC LVTT: 000000ef
[ 3.052722] ... APIC LVT0: 00010700
[ 3.052722] ... APIC LVT1: 00000400
[ 3.052722] ... APIC LVTERR: 000000fe
[ 3.052722] ... APIC TMICT: 0002c1a8
[ 3.052722] ... APIC TMCCT: 00000000
[ 3.052722] ... APIC TDCR: 00000003
[ 3.052722]
[ 3.076566] number of MP IRQ sources: 15.
[ 3.076609] number of IO-APIC #1 registers: 24.
[ 3.076636] testing the IO APIC.......................
[ 3.081928] IO APIC #1......
[ 3.081968] .... register #00: 01000000
[ 3.081997] ....... : physical APIC id: 01
[ 3.082022] ....... : Delivery Type: 0
[ 3.082047] ....... : LTS : 0
[ 3.082073] .... register #01: 00170020
[ 3.082100] ....... : max redirection entries: 17
[ 3.082126] ....... : PRQ implemented: 0
[ 3.082152] ....... : IO APIC version: 20
[ 3.082176] .... IRQ redirection table:
[ 3.082200] NR Dst Mask Trig IRR Pol Stat Dmod Deli Vect:
[ 3.082235] 00 00 1 0 0 0 0 0 0 00
[ 3.082292] 01 01 0 0 0 0 0 1 1 31
[ 3.082345] 02 01 0 0 0 0 0 1 1 30
[ 3.082399] 03 01 0 0 0 0 0 1 1 33
[ 3.082452] 04 01 0 0 0 0 0 1 1 34
[ 3.082505] 05 01 0 0 0 0 0 1 1 35
[ 3.082558] 06 01 0 0 0 0 0 1 1 36
[ 3.082611] 07 01 0 0 0 0 0 1 1 37
[ 3.082664] 08 01 0 0 0 0 0 1 1 38
[ 3.082718] 09 01 0 1 0 0 0 1 1 39
[ 3.082771] 0a 01 0 0 0 0 0 1 1 3A
[ 3.082824] 0b 01 0 0 0 0 0 1 1 3B
[ 3.082878] 0c 01 0 0 0 0 0 1 1 3C
[ 3.082931] 0d 01 0 0 0 0 0 1 1 3D
[ 3.082985] 0e 01 0 0 0 0 0 1 1 3E
[ 3.083038] 0f 01 0 0 0 0 0 1 1 3F
[ 3.083092] 10 01 0 1 0 1 0 1 1 71
[ 3.083146] 11 01 1 1 0 1 0 1 1 81
[ 3.083199] 12 00 1 0 0 0 0 0 0 00
[ 3.083253] 13 01 1 1 0 1 0 1 1 61
[ 3.083306] 14 01 1 1 0 1 0 1 1 41
[ 3.083360] 15 01 1 1 0 1 0 1 1 51
[ 3.083413] 16 00 1 0 0 0 0 0 0 00
[ 3.083467] 17 00 1 0 0 0 0 0 0 00
[ 3.083511] IRQ to pin mappings:
[ 3.083542] IRQ0 -> 0:2
[ 3.083583] IRQ1 -> 0:1
[ 3.083625] IRQ3 -> 0:3
[ 3.083665] IRQ4 -> 0:4
[ 3.083702] IRQ5 -> 0:5
[ 3.083743] IRQ6 -> 0:6
[ 3.083779] IRQ7 -> 0:7
[ 3.083820] IRQ8 -> 0:8
[ 3.083857] IRQ9 -> 0:9
[ 3.083897] IRQ10 -> 0:10
[ 3.083935] IRQ11 -> 0:11
[ 3.083976] IRQ12 -> 0:12
[ 3.084013] IRQ13 -> 0:13
[ 3.084054] IRQ14 -> 0:14
[ 3.084092] IRQ15 -> 0:15
[ 3.084133] IRQ16 -> 0:16
[ 3.084174] IRQ17 -> 0:17
[ 3.084215] IRQ19 -> 0:19
[ 3.084253] IRQ20 -> 0:20
[ 3.084292] IRQ21 -> 0:21
[ 3.084331] .................................... done.
[ 3.089511] Using IPI Shortcut mode
[ 3.106668] Magic number: 9:319:800
[ 3.110618] bdi mtd-rwmap: hash matches
[ 3.126907] Freeing unused kernel memory: 272k freed
[ 3.135043] Write protecting the kernel text: 3100k
[ 3.141224] Write protecting the kernel read-only data: 1284k
[ 3.147024] NX-protecting the kernel data: 3044k
[ 3.170639] mmc0: new high speed SDHC card at address 59b4
[ 3.196486] mmcblk0: mmc0:59b4 NCard 29.5 GiB
[ 3.231162] tsc: Refined TSC clocksource calibration: 399.076 MHz
[ 3.237496] Switching to clocksource tsc
[ 3.252067] mmcblk0: p1
>[ 3.381545] udevd[542]: starting version 182
[ 8.759986] kjournald starting. Commit interval 5 seconds
[ 8.768894] EXT3-fs (loop0): using internal journal
[ 8.774081] EXT3-fs (loop0): mounted filesystem with writeback data mode
[ 10.338813] IOAPIC[0]: Set routing entry (1-18 -> 0x91 -> IRQ 18 Mode:1 Active:1 Dest:1)
[ 10.341093] pch_udc 0000:00:14.2: setting latency timer to 64
[ 10.341499] pch_udc 0000:00:14.2: irq 40 for MSI/MSI-X
[ 10.342113] pch_udc 0000:00:14.2: enabling Mem-Wr-Inval
[ 10.443242] g_serial: Vendor 0x8086 Product 0xbabe
[ 10.448188] g_serial gadget: Gadget Serial v2.4
[ 10.453325] g_serial gadget: g_serial ready
[ 10.545308] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 10.552274] stmmaceth 0000:00:14.6: enabling bus mastering
[ 10.552360] stmmaceth 0000:00:14.6: setting latency timer to 64
[ 10.552749] stmmaceth 0000:00:14.6: irq 41 for MSI/MSI-X
[ 10.552998] stmmac MSI mode enabled
[ 10.556362] Vendor 0x8086 Device 0x0937
[ 10.560723] stmmac - user ID: 0x10, Synopsys ID: 0x37
[ 10.565827] DMA HW capability register supported
[ 10.570519] Enhanced/Alternate descriptors
[ 10.574948] RX Checksum Offload Engine supported (type 2)
[ 10.580590] TX Checksum insertion supported
[ 10.584911] Enable RX Mitigation via HW Watchdog Timer
[ 10.646714] libphy: stmmac: probed
[ 10.650321] eth0: PHY ID 20005c90 at 1 IRQ 0 (stmmac-1:01) active
[ 10.759275] ACPI: bus type usb registered
[ 10.766951] usbcore: registered new interface driver usbfs
[ 10.774835] usbcore: registered new interface driver hub
[ 10.783078] usbcore: registered new device driver usb
[ 10.809636] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 10.886066] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.893293] ohci_hcd 0000:00:14.4: enabling bus mastering
[ 10.893379] ohci_hcd 0000:00:14.4: setting latency timer to 64
[ 10.893443] ohci_hcd 0000:00:14.4: OHCI Host Controller
[ 10.899897] ohci_hcd 0000:00:14.4: new USB bus registered, assigned bus number 1
[ 10.907769] ohci_hcd 0000:00:14.4: irq 16, io mem 0x9000c000
[ 10.991869] hub 1-0:1.0: USB hub found
[ 10.996280] hub 1-0:1.0: 2 ports detected
[ 11.075075] ehci-pci: EHCI PCI platform driver
[ 11.080150] ehci-pci 0000:00:14.3: enabling bus mastering
[ 11.080241] ehci-pci 0000:00:14.3: setting latency timer to 64
[ 11.080304] ehci-pci 0000:00:14.3: EHCI Host Controller
[ 11.086166] ehci-pci 0000:00:14.3: new USB bus registered, assigned bus number 2
[ 11.094823] ehci-pci 0000:00:14.3: enabling Mem-Wr-Inval
[ 11.094995] ehci-pci 0000:00:14.3: INSNREG01 is 0x007f007f
[ 11.101893] ehci-pci 0000:00:14.3: INSNREG01 is 0x007f007f
[ 11.109267] ehci-pci 0000:00:14.3: irq 19, io mem 0x9000d000
[ 11.130249] ehci-pci 0000:00:14.3: USB 2.0 started, EHCI 1.00
[ 11.142563] hub 2-0:1.0: USB hub found
[ 11.146576] hub 2-0:1.0: 2 ports detected
[ 11.242128] Initializing USB Mass Storage driver...
[ 11.249249] usbcore: registered new interface driver usb-storage
[ 11.255493] USB Mass Storage support registered.
[ 11.473644] intel_cln_gpio_probe UIO addr 0x90006000 internal_addr 0x00000000 size 3765649408 memtype 4096
[ 11.494877] intel_cln_gip 0000:00:15.2: setting latency timer to 64
[ 11.495278] intel_cln_gip 0000:00:15.2: irq 42 for MSI/MSI-X
[ 11.568166] cy8c9540a 0-0020: dev_id=0x40
[ 11.751674] at24 0-0050: byte_len looks suspicious (no power of 2)!
[ 11.758132] at24 0-0050: 11264 byte at24 EEPROM, writable, 1 bytes/write
[ 11.828578] i2c /dev entries driver
[ 12.050409] spi_pxa2xx_pci: `0' invalid for parameter `gpio_cs'
[ 12.117155] ce4100_spi 0000:00:15.0: enabling device (0000 -> 0002)
[ 12.124279] ce4100_spi 0000:00:15.0: enabling bus mastering
[ 12.124366] ce4100_spi 0000:00:15.0: setting latency timer to 64
[ 12.124777] ce4100_spi 0000:00:15.0: irq 43 for MSI/MSI-X
[ 12.127499] ce4100_spi 0000:00:15.1: enabling device (0000 -> 0002)
[ 12.134617] ce4100_spi 0000:00:15.1: enabling bus mastering
[ 12.134704] ce4100_spi 0000:00:15.1: setting latency timer to 64
[ 12.135116] ce4100_spi 0000:00:15.1: irq 44 for MSI/MSI-X
[ 12.149028] pxa2xx-spi pxa2xx-spi.0: registered master spi0
[ 12.149909] spi_master spi0: will run message pump with realtime priority
[ 12.160446] spi spi0.0: 1000000 Hz actual, PIO
[ 12.160833] spi spi0.0: setup mode 2, 8 bits/w, 5000000 Hz max --> 0
[ 12.165550] pxa2xx-spi pxa2xx-spi.0: registered child spi0.0
[ 12.167988] pxa2xx-spi pxa2xx-spi.1: registered master spi1
[ 12.168861] spi_master spi1: will run message pump with realtime priority
[ 12.176123] spi spi1.0: 5000000 Hz actual, PIO
[ 12.176229] spi spi1.0: setup mode 0, 8 bits/w, 50000000 Hz max --> 0
[ 12.187755] pxa2xx-spi pxa2xx-spi.1: registered child spi1.0
[ 12.492557] cfg80211: Calling CRDA to update world regulatory domain
[ 12.535795] Intel(R) Wireless WiFi driver for Linux, in-tree:
[ 12.541726] Copyright(c) 2003-2012 Intel Corporation
[ 12.809415] Bluetooth: Core ver 2.16
[ 12.814799] NET: Registered protocol family 31
[ 12.819300] Bluetooth: HCI device and connection manager initialized
[ 12.826873] Bluetooth: HCI socket layer initialized
[ 12.832014] Bluetooth: L2CAP socket layer initialized
[ 12.837381] Bluetooth: SCO socket layer initialized
[ 12.859605] usbcore: registered new interface driver btusb
[ 12.943507] usbcore: registered new interface driver usbhid
[ 12.949133] usbhid: USB HID core driver
[ 16.202374] eth0: device MAC address **:**:**:**:**:**
[ 26.974760] NET: Registered protocol family 10
[ 27.044662] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready まとめ
ログからわかる情報も結構多いものだと思います。これらのログが何らかのヒントになれば幸いです。